OPERATION
5.
6.
Once the engine starts, release starter button.
NOTE: When selecting a Drive Speed, use the slower speeds until
you are comfortable and familiar with the operation of the snow
thrower.
As the engine warms, slowly rotate choke control to the OFF
position. If the engine falters, quickly rotate choke control back to
FULL
then slowly into the OFF position again.
2.
Squeeze the drive control against the handle the snow thrower
will move. Release it and drive motion will stop.
7.
When disconnecting the extension cord, always unplug the end
at the three-prong wall outlet before unplugging the opposite end
from the snow thrower.
NOTE: NEVER reposition the shift lever (change speeds or direction
of travel) without first releasing the drive control and bringing the snow
thrower to a complete stop. Doing so will result in premature wear to
the snow thrower’s drive system.
r ecoil Starter
1.
Rotatestart). choke control to FULL
choke position (cold engine
To engage aUger S
NOTE: If the engine is already warm, place choke control in the OFF
1.
To engage the augers and start throwing snow, squeeze the
auger control against the left handle. Release to stop the augers.
position instead of FULL
.
2.
Push the primer two or three times for cold engine start, making
sure to cover vent hole in the center of the primer when pushing.
r ePLaCing SHear PinS
The augers are secured to the spiral shaft with two shear pins and cot-
ter pins. If the auger should strike a foreign object or ice jam, the snow
thrower is designed so that the shear pins may shear. If the augers will
not turn, check to see if the pins have sheared. See Figure 12.
NOTE:shutdown.DO NOT use primer to restart a warm engine after a short
NOTE: Additional priming may be necessary if the temperature is
below 15° Fahrenheit.
CaUTio n
NEVER replace the auger shear pins with anything other than OEM
Part No. 738-04124A replacement shear pins. Any damage to the
auger gearbox or other components as a result of failing to do so will
NOT be covered by your snow thrower’s warranty.
3.
4.
5.
Grasp the recoil starter handle and slowly pull the rope out. At the
point where it becomes slightly harder to pull the rope, slowly
allow the rope to recoil.
Pull the starter handle with a firm, rapid stroke. Do not release
the handle and allow it to snap back. Keep a firm hold on the
starter handle and allow it to slowly recoil.
War ning
As the engine warms, slowly rotate the choke control to the OFF
position. If the engine falters, quickly rotate the choke control
Always turn off the snow thrower’s engine and remove the key prior to
replacing shear pins.
back to the FULL
position again.
position and then slowly into the OFF
NOTE: Allow the engine to warm up for a few minutes after starting.
The engine will not develop full power until it reaches operating
temperatures.
SToPPing THe engine
Run engine for a few minutes before stopping to help dry off any
moisture on the engine.
1.
2.
3.
Move throttle control to STOP
position.
STOP
Remove the ignition key and store in a safe place.
Wipe all snow and moisture from the area around the engine as
well as the area in and around the drive control and auger control.
Also, engage and release both controls several times.
To engage Dr ive
1.
With the throttle control in the Fast
position, move shift lever
into one of the six forward (F) positions or two reverse (R)
positions. Select a speed appropriate for the snow conditions and
a pace you’re comfortable with.
Figure 12
1
| Categories | Craftsman Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Craftsman 247.88045 |
| Model Number | 247.88045 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Español |
| Product Name | Craftsman 45-Inch Snow Thrower |
| Product Brand | Craftsman. Customer Service Representatives are available by phone: Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Swath | 45 inch |
| Engine Manufacturer | Craftsman |
| Engine Oil Type | SAE 5W30, 4-Cycle Engine Oil (Quart) Recommended for Temperature: - Above 32°F: SAE 30W Straight Grade; - 0°F to 32°F: SAE 5W-30 or SAE 10W-30 Multi Grade; - Below O°F: SAE 0W-30 Synthetic |
| Engine Motor Model # | OH358SA-223828 |
| Document File Type | |
| Publisher | craftsman.com |
| Wikipedia's Page | Craftsman (tools) |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)