10
IMPORTANT: Used motor oil may cause skin cancer
if repeatedly left in contact with the skin for prolonged
periods. Although this is unlikely unless you handle used
oil on a daily basis, it is still advisable to thoroughly wash
your hands with soap and water as soon as possible
after handling used oil.
0APER�%LEMENT
NOTE: Please dispose of used motor oil in a manner that
is compatible with the environment. We suggest you take
it in a sealed container to your local service station for
reclamation. Do not throw it in the trash or pour it on the
ground.
Maintaining
Your
Engine
Air Cleaner Service
A dirty air cleaner will restrict air flow to the carburetor.
To prevent carburetor malfunction, service the air cleaner
regularly. Service more frequently when operating the
engine in extremely dusty areas.
&OAM�%LEMENT
Figure 10-2
WARNING: Never use gasoline or low
flash point solvents for cleaning the
air cleaner element. A fire or explosion
could result.
IMPORTANTcleaner. Rapid: Neverenginerunwearthewillengineresult.without the air
3PARK�0LUG
WARNING
Never use gasoline
or low flash point sol-
vents for cleaning the
air cleaner element.
A fire or explosion
could result.
1.
Remove the wing bolt and the air cleaner cover.
Remove the elements and separate them. See Figure
10-2.
Carefully check both elements for holes or tears
and replace if damaged.
2.
Foam element: Wash the element in a solution of
household detergent and warm water, then rinse
thoroughly, or wash in nonflammable or high flash
point solvent. Allow the element to dry thoroughly.
Soak the element in clean engine oil and squeeze out
the excess oil. The engine will smoke during initial
start-up if too much oil is left in the foam.
Paper element: Tap the element lightly several times
on a hard surface to remove excess dirt, or blow
compressed air through the filter from the inside out.
Never try to brush the dirt off; brushing will force
dirt into the fibers. Replace the paper element if it is
excessively dirty.
3PARK�0LUG�"OOT
DO NOT check for
spark with spark plug
removed. DO NOT
crank engine with
spark plug removed.
Figure 10-3
WARNING: If the engine has been
running, the muffler will be very hot. Be
careful not to touch the muffler.
Visually inspect the spark plug. Discard the spark plug
if there is apparent wear, or if the insulator is cracked
or chipped. Clean the spark plug with a wire brush if it
is to be reused.
3.
2.
If the engine has
been running, the
muffler will be very
hot. Be careful not to
touch the muffler.
Foam Element Part Number: 751-10239
Paper Element Part Number: 751-10240
Spark Plug Service
3.
4.
5.
Measure the plug gap with a feeler gauge. Correct
as necessary by bending side electrode. See Figure
1
0-4. The gap should be: 0.030 in.
Check that the spark plug washer is in good condition
and thread the spark plug in by hand to prevent
cross-threading.
Afterplug wrenchthe sparkto compressplug is seated,the washer.tighten with a spark
NOTE: When installing a new spark plug, tighten 1/2 turn
after the spark plug seats to compress the washer. When
reinstalling a used spark plug, tighten 1/8-1/4 turn after
the spark plug seats to compress the washer.
WARNING: DO NOT check for spark
with spark plug removed. DO NOT
crank engine with spark plug removed.
Tobe ensureproperlypropergappedengineand freeoperation,of deposits.the spark plug must
1.
Removewrench totheremovesparktheplugplug.bootSeeandFigureuse a spark10-3. plug
1
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals |
|---|---|
| Tags | MTD 56M |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)