8.
9.
Insert the bump on the second lower blower tube into the bump slot on the nozzle (Fig. 5, A).
Twist the nozzle clockwise around the second lower blower tube until the nozzle bump locks into
place (Fig. 5, B).
KNOW YOUR UNIT
Starter Rope
Handle
Air Filter Cover
Choke Lever
Fuel
Cap
Suspension System
A
B
A
B
Fig. 4
Fig. 5
Shoulder Support
The completed blower tube should look like Figure 6.
Elbow Tube
Shoulder Support Buckle
Hose Clamp
Stand
Throttle Cables
Trigger Lock
Waist Support
Throttle Cables
Flex Tube
Throttle Grip
Waist Support
Clip
Hose Clamp
Trigger
Muffler
Upper Blower Tube
On/Off Switch
Throttle Grip
Blower Tube
First Lower Blower
Tube
Primer Bulb
Nozzle
Fuel Tank
Second Lower Blower
Tube
ASSEMBLY INSTRUCTIONS
Nozzle
ASSEMBLING THE BLOWER TUBE
WARNING: To avoid serious personal injury
and damage to the unit, shut the unit off before
removing or installing the blower tubes.
B
C
Installing the Flex Tube
D
Fig. 6
1.
2.
Place a hose clamp over the end of the Flex Tube (Fig. 1A).
Slide the end of the Flex Tube with the clamp on it over the
elbow tube (Fig. 1B).
A
WARNING: To avoid serious personal injury, make sure that all four parts of the
blower tube are locked in place or firmly installed.
3.
4.
Align the bump on the Flex Tube with the bump on the elbow
tube (Fig. 1C).
Tighten the screw on the hose clamp to secure the Flex Tube
to the elbow tube (Fig. 1D).
Fig. 1
Secure the Throttle Cables
Place a zip tie around the elbow tube and the throttle cables
(Fig. 7) as shown, making sure not to crimp the cables.
Zip Tie
Installing the Upper Blower Tube
1.
2.
3.
4.
Place a hose clamp over the other end of the Flex Tube (Fig.
2, A).
Slide the end of the hose with the clamp on it over the top
end of the upper blower tube (Fig. 2, B).
Align the bump on the Flex Tube with the bump on the upper
blower tube (Fig. 2, C).
Adjusting the Handle
C
WARNING: Do not rotate the handle clockwise
to adjust. This may cause the throttle cables to
disconnect from the throttle grip or the engine.
D
A
B
Tighten the screw on the hose clamp to secure the Flex Tube
to the upper blower tube (Fig. 2, D).
1.
2.
3.
Rotate the throttle grip counterclockwise around the blower tube
until it is pointing directly downward (Fig. 8, A).
Fig. 2
Installing the Lower Blower Tubes and Nozzle
1.
Pull or push the throttle grip along the handle tube until its
distance from the backpack blower is comfortable (Fig. 8, B).
Align the throttle grip with the slot closest to the comfortable
place and rotate the throttle grip clockwise into the upright
position (Fig. 9).
Align the bump slot on the end of the first lower blower tube
with the bump on the bottom end of the upper blower tube
(Fig. 3, A).
Insert the bump on the upper blower tube into the bump slot
on the tube extension (Fig. 3, A).
Twist the extension tube clockwise around the upper upper
blower tube until the handle tube bump locks into place (Fig.
3, B).
Zip Tie
Fig. 7
2.
3.
B
4.
Align the bump slot on the end of the second lower blower
tube with the bump on the bottom end of the first lower
blower tube (Fig. 4, A).
A
5.
6.
Insert the bump on the first lower blower tube into the bump
slot on the second lower blower tube (Fig. 4, A).
Twist the second lower blower tube clockwise around the first
lower blower tube until the second lower blower tube bump
locks into place (Fig. 4, B).
A
B
Fig. 3
Fig. 8
Fig. 9
7.
Align the bump slot on the top end of the nozzle with the bump on the bottom end of the second
lower blower tube (Fig. 5, A).
5
| Categories | Lawn Mower Manual, MTD Blower and Vacuum Manuals, MTD Lawn Mower Manuals, Troy-Bilt Blower and Vacuum Manuals, Troy-Bilt Lawn Mower Manuals |
|---|---|
| Tags | MTD TB2BP, Troy-Bilt TB2BP |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)