8
Problem Possible Cause(s) Solution
Engine fails to start
1. Fuel tank empty, or stale fuel
1. Fill tank with clean fresh gasoline.
2. Mix new fuel at a ratio of 50:1
3. Clean fuel line
4. Insert key and turn to ON position
5. Connect wire to spark plug.
6. Cleansparkplug, readjust gap, or
replace.
2.
3.
4.
5.
Improper fuel mixture
Blocked fuel line
Key not in ON position
Spark plug wire disconnected
Trouble-
6. Faultysparkplug
Shooting
7.
8.
Engine not primed
Engine flooded from excessive
priming
7. Prime engine four times.
8. Wait at least ten minutes before
starting.
Engine runs erratic
1. Unit running on choke
1. Move choke lever to OFF position.
2. Clean fuel line and fill tank with
fresh, clean gasoline.
2.
Fuel line blocked, or stale fuel
3.
4.
Water or dirt in fuel system
Carburetor out of adjustment
3. Refer to engine manual for remedy.
4. Refer to engine manual for remedy.
PleasedoNOT
returntheunittothe
retailerfromwhichitwas
purchased,withoutfirst
contactingCustomer
Support.
Engine overheats
Loss of power
1. Carburetor out of adjustment
1. Refer to engine manual for instruction.
1. Spark plug wire loose
1. Firmlyconnect sparkplugwire.
2. Vent ingascapplugged
2. Clear vent.
Excessive vibration
1. Loose parts or damaged auger
1. Stop engine immediately and
disconnect spark plug wire. Check
for possibledamage. Tightenall
bolts and nuts. Repair as needed. If
the problem persists, take unit to an
authorized service dealer.
Logonto
www.whiteoutdoor.com
orcall acustomer
servicerepresentative
at 1(800) 949-4483
Unit fails to self-propel
1. Drivecableout of adjustment
1. Adjustcontrol cablefollowinginstruc-
tions on page 9 of this manual.
2. Replace drive belt.
2.
Drive belt loose or damaged
Note:
You will need the
Augers continue to rotate 1. Cable out of adjustment.
1. Adjust auger control cable as
shown in “Making Adjustments” on
page 10.
model number and
serial number if and
when calling Customer
Support, logging
onto our website and
contacting a service
dealer. Please refer
to page 2 of this
manual for information
regarding locating and
recording your model
and serial numbers.
Unit fails to discharge
snow
1.
Chute assembly clogged.
1. Stop engine and disconnect spark
plug wire. Clean chute and inside
of auger housingwithclean-out
tool or stick.
2.
3.
Replace shear pin.
2.
3.
Shear pin sheared.
Foreign object lodged in auger.
Stop engine immediately and
disconnect thesparkplugwire.
Remove object from auger.
Adjust auger control cable.
4.
5.
4
. Auger control cableout of
adjustment.
Replace auger belt.
5.
Auger belt loose or damaged.
NOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized service representative or
call 1-866-949-4483 for the Customer Support Center. Refer to the engine manual for more engine related information.
13
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, White Outdoor Snow Blower Manuals |
|---|---|
| Tags | MTD 235, MTD S235, MTD Snow Blower Manual, White Outdoor 235, White Outdoor S235 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)