MTD Yard Machines E762F Snow Blower Owners Manual

SECTION 5:  ASSEMBLY INSTRUCTIONS
IMPORTANT: After   assembly,    service   engine
with gasoline, and check oil level as instructed in the
separate engine manual packed with your unit.
Attaching the Handle Assembly.
(Hardware A)
Lay loose parts out on flat surface.
NOTE: All  references  to  right  or  left  side  of  the
snow thrower are determined from behind the unit in
the operating position.
1.   Handle Panel
2.   Right Handle
5.   Traction Drive Control
Grip
6.   Right Grip Bracket
3.
4.
Left Handle
7.
Left Grip Bracket
Auger Control Grip
UNPACKING
1.
Remove staples or break glue on the top flaps of
the   carton.    Remove   any    loose   parts    like
operator’s  manual  or  hardware   pack  included
with unit.
1
2.
Cut the carton along its corners and lay the end
of   the   carton    down   flat.   Remove    packing
material.
3.
4.
5.
Roll unit out of carton. Check carton thoroughly
for loose parts.
7
6
5
4
Extend cables out behind unit and lay them on
the floor.
Lay  out   the   contents  of   the  hardware   pack
according  to   the   illustration  on   page  5   and
identify each part.
2
3
6.
Find the loose parts in the carton and lay these
on  the  floor.  You   should  locate  the  following
loose parts in the carton:
Figure 2  
1.   Attach  left   handle  and  grip  bracket  to  handle
panel with two carriage  bolts, lock washers and
hex nuts. (Be sure the bend in the grip bracket is
towards  the  center  of  the  handle  panel.  (See
Figure 3.) Do not tighten at this time.
1
2
3
.
.
.
Handle Panel
Right Handle
Left Handle
4.
Auger Control Grip
5.
6.
7.
8.
9.
10.
11.
Traction Drive Control Grip
Right Clutch Grip Bracket
Left Clutch Grip Bracket
Shift Rod (Not Illustrated)
Chute Crank Assembly (Not Illustrated)
Chute Assembly (Not Illustrated)
Hardware Pack (Not Illustrated)
Handle Panel
Outer
Edge
of Handle
Panel
Left Grip Bracket
Carriage
Bolts
Tools Required
The  snow  thrower  comes  partly  assembled  in  the
carton.  You  will  have   to  complete  the  assembly.
Follow   assembly   instructions    in   this   operator’s
manual to make the job safe and easy. You will need
the following tools to assemble the snow thrower.
Left Handle
(curves in)
Lock Washers
and Hex Nuts
A.
B.
Set of Wrenches (3/8", 9/16", 1/2" or
adjustable)
Pair of pliers
Figure 3  
2.
Locate  auger  control  grip,  part  #4  in  Figure  2.
The  triangular  metal  tab  on  the  auger  control
grip must face the center of the handle panel.
6
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, Yard Machines Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 30 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower, Yard Machines, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website