ENGLISH
5.
(Figure 19) Loosen the belt guide (9). Pull
the belt guide (9) away from the auger
drive pulley (10).
12.Adjust the belt guide (9). See “How To Ad-
just The Belt Guide” in the Maintenance sec-
tion.
3. (Figure 23) Move the friction wheel (4) to
the correct position.against the snap ring
(1).
6.
7.
Pull the idler pulley (3) away from the auger
drive belt (4).
Remove the old auger drive belt (4) from
13.(Figure 21) Install the bottom panel (2).
14.Tighten the bolts (3) on each side of the bot-
tom panel (2).
the auger drive pulley (10) and from the en- 15.(Figure 18) Install the belt cover (1). Tighten
screw (2).
4. (Figure 8) Turn the adaptor (10) until the
ball joint (6) is aligned with the mounting
hole in the shifter rod (7). When aligned,
attach the ball joint (6) to the shifter rod (7).
5.
(Figure 21) Install the bottom panel (2).
gine pulley (11). Replace the auger drive
belt (4) with an original factory replacement
belt available from an authorized service
center.
Install the new auger drive belt (4) onto the
auger drive pulley (10) and onto pulley
6. Tighten the bolts (3) on each side of the bot-
tom panel (2).
16.
17.
Check the adjustment of the cables. See
“How To Check And Adjust The Cables” in
the Maintenance section.
How To Replace The Friction Wheel
8.
Connect the spark plug wire.
If the friction wheel is worn or damaged, the
snow thrower will not move forward. The friction
wheel must be replaced as follows.
(11).
How To Adjust The Belt Guide
9.
Adjust the auger drive belt (4). See “How To
Adjust The Auger Drive Belt” in the Mainte-
nance section.
Adjust the belt guide (9). See “How To Ad-
just The Belt Guide” in the Maintenance sec-
tion.
(Figure 18) Install the belt cover (1). Tighten
screw (2).
Check the adjustment of the cables. See
“How To Check And Adjust The Cables” in
the Maintenance section.
1.
Disconnect spark plug wire.
1. (Figure 2) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
WARNING: Drain the gasoline out-
doors, away from fire or flame.
2. (Figure 18) Remove screw (2). Remove the
belt cover (1).
3. (Figure 2) Engage the auger drive lever (5).
4. (Figure 22) Measure the distance between
the belt guide (2) and auger drive belt (3).
The correct distance (4) is 1/8 inch (3.175
mm).
10.
11.
12.
2.
Disconnect the spark plug wire.
3. (Figure 27) Remove the fasteners that se-
cure the right wheel (10). Remove the right
wheel (10) from the axle (11).
4. Loosen the bolts (3) on each side of the bot-
tom panel (2).
5. Remove the bottom panel (2).
6. (Figure 28) Remove the fasteners that se-
cure the drive sprocket (12) to the axle (11).
7. Remove the left wheel, axle (11), and drive
sprocket (12).
5.
If an adjustment is necessary, loosen the
mounting bolt for the belt guide (2). Move
the belt guide (2) to the correct position
13.
14.
(Figure 21) Install the bottom panel (2).
Tighten the bolts (3) on each side of the bot-
tom panel (2).
(4). Tighten the mounting bolt for the belt
guide (2).
6.
7.
(Figure 18) Install the belt cover (1). Tighten
screw (2).
Connect the spark plug wire.
15.
Connect the spark plug wire.
How To Remove the Traction Drive Belt
8.
(Figure 29) Remove the four bolts (16) that
hold the bearings (7) on each side of the
hex shaft (8).
How To Adjust Or Replace The Friction
Wheel
If the snow thrower will not move forward, check
the traction drive belt for wear or damage. If the
traction drive belt is worn or damaged, replace
the belt as follows.
9. (Figure 30) Remove the hex shaft (8) and
bearings (7).
How To Check The Friction Wheel
NOTE: Take special note of the position of
the washers (17) .
(Figure 24) Remove the three fasteners (4)
that hold the friction wheel (5) to the hub
(6).
(Figure 24) Remove the friction wheel (5)
from the hub (6). Slip the friction wheel (5)
off the hex shaft (8).
Assemble the new friction wheel (5) onto
hub (6) with the fasteners removed earlier.
(Figure 30) Install the hex shaft (8) and
bearings (7) with the four bolts removed ear-
lier.
1.
2.
Disconnect the spark plug wire.
If the snow thrower will not move forward, check
the traction drive belt, the traction drive cable or
the friction wheel. If the friction wheel is worn or
damaged, it must be replaced. See “How To
Replace the Friction Wheel” in this section. If the
friction wheel is not worn or damaged, check as
follows.
Remove the auger drive belt. See “How To
Remove The Auger Drive Belt” in the Mainte-
nance section.
(Figure 19) Remove the e-ring (17) from
one end of the swing plate axle rod (18).
Remove the swing plate axle rod (18) to
allow the the swing plate to pivot forward.
10.
11.
3.
1.
(Figure 2) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
12.
13.
4.
5.
Remove the traction drive spring (16).
Remove the old traction drive belt (13) from
the traction drive pulley (14) and from the
engine pulley (15). Replace the traction
drive belt (13) with an original factory re-
placement belt available from an authorized
service center.
Install the new traction drive belt (13) onto
the traction drive pulley (14) and onto en-
gine pulley (15).
WARNING: Drain the gasoline out-
doors, away from fire or flame.
Make sure the washers (17) are properly
installed in the original position. Also,
make sure the two washers (13) are prop-
erly aligned with the actuator arms (14).
2.
3.
Disconnect the spark plug wire.
(Figure 21) Loosen the bolts (3) on each
side of the bottom panel (2).
6.
7.
4.
5.
Remove the bottom panel (2).
(Figure 2) Position the shift speed lever (6)
14.Make sure the hex shaft (8) turns freely.
15.
(Figure 28) Install the left wheel, axle (11),
and drive sprocket (12) with the fasteners
removed earlier. Install the chain (15) onto
the drive sprocket (12).
Check the adjustment of the friction wheel.
See “How To Adjust The Friction Wheel” in
this section.
17.Make sure the friction wheel and the disc
drive plate are free from grease or oil.
18.(Figure 21) Install the bottom panel (2).
19.Tighten the bolts (3) on each side of the bot-
tom panel (2).
20.(Figure 27) Install the right wheel (10) to the
axle (11) with the fasteners removed earlier.
21.Connect the spark plug wire.
Make sure the traction drive idler pulley
in the lowest forward speed.
(12)
is properly aligned with the traction
6.
(Figure 23) Note the position of the friction
wheel (4). The correct distance “A” from the
right side of the friction wheel (4) to the out-
side of the motorbox is as follows:
drive belt (13).
Attach the traction drive spring (16).
Install the swing plate axle rod (18) and se-
cure with the e-ring (17) removed earlier.
(Figure 29) The bottom of the swing plate
8.
9.
16.
Tire Size
Distance “A”
10.
12
16
and 13 inch
inch
4-1/8” (10.5 cm.)
4-5/16” (10.95 cm.)
(20)
must be positioned between the align-
ment tabs (19). Make sure the swing plate
is properly secured.
If the friction wheel (4) is not in the correct
position, adjust as follows.
(20)
NOTE: If the drive will not engage after
the traction drive belt has been replaced,
then check to make sure that the swing
plate is positioned between the alignment
tabs (19).
How To Adjust The Friction Wheel
1. (Figure 2) Position the shift speed lever (6)
in the lowest forward speed.
2. (Figure 8) Loosen hex jam nut (9) on speed
select rod (2). Remove ball joint (6) from
How To Replace the Auger Shear Bolt
The augers are secured to the auger shaft with
special shear bolts. These shear bolts are de-
11.
(Figure 19) Install and adjust the auger
drive belt (4). See “How To Remove The
Auger Drive Belt” in the Maintenance section.
shifter rod (7).
F-031086L
18
| Categories | Murray Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Murray 629108X84A |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Murray 629108X84A Snow Blower Owners Manual 5.0 out of 5.0 based on 1 product reviews. I have been using this snow blower for over 10 years.
Need to download the menu to change a belt