A WARNING
4. Broken belt. Replace belt.
Shear pin broken. Replace pin.
5.
Before performing any adjustment or service to
snowthrower, stop the engine and wait for moving
parts to stop. Remove the key. To prevent acciden-
tal starting, disconnect the spark plug wire and
fasten away from the plug.
Auger rotates, but snow not thrown far enough.
Spout deflector too low. Adjust deflector as neces-
sary.
2.
3.
4.
Engine speed too slow. Set to full throttle.
Ground speed too fast. Use slower speed.
This section provides troubleshooting and service
instructions. For problems not covered here, contact your
dealer.
Snowthrower discharge spout clogged. STOP engine
and REMOVE the key. DISCONNECT the spark plug
wire. Clear auger using a narrow board. See warning
in SAFETY RULES.
TROUBLESHOOTING
Locate the problem and check the possible cause/reme-
dy in the order listed. Also, refer to the engine manufac-
turer’s Owner’s Manual for other information. If problem
cannot be remedied, see your dealer.
Scraper bar does not clean hard surface.
Skid shoes improperly adjusted. Adjust.
Snowthrower picks up and throws stones on gravel
drive.
Engine fails to start.
1.
2.
3.
4.
Key off. Push key in to the ON position.
Fuel valve closed. Turn valve to open position.
Out of fuel. Fill fuel tank.
1. Skid shoes improperly adjusted. Adjust.
Poor traction.
Tires slipping. Check tire pressure and tread.
Auger does not stop when auger lever is released.
drive belt out of adjustment. Adjust auger belt.
Choke not on. Turn choke fully clockwise to ON posi-
tion and set throttle up to FAST position.
5.
6.
Engine flooded. Move choke to counterclockwise to
OFF position and try starting engine again.
Snowthrower does not stop when drive lever is
released.
Spark plug faulty, fouled or poorly gapped. Clean and
gap or replace.
Unit drive belt out of adjustment. Adjust drive belt.
Snowthrower does not drive when drive lever is
engaged.
7.
8.
Water in fuel. Drain tank and refill with fresh fuel.
Old stale gas. Drain tank and refill with fresh fuel.
1.
Drive belts loose, broken or stretched. Adjust or
replace.
Engine starts hard or runs poorly.
Fuel mixture too rich. Move choke to OFF position.
2. Drive roller chain damaged. Replace chain.
Discharge control is difficult to operate.
1. Gears need lubrication. Oil as required.
Cannot shift into all speeds.
2.
3.
Carburetor adjusted incorrectly. See your dealer.
Spark plug faulty, fouled or poorly gapped. Clean and
gap or replace.
4.
Fuel cap vent blocked. Clear vent.
See SHIFT CONTROL ADJUSTMENT.
Snowthrower veers to one side.
Auger does not rotate.
Auger control clutch lever not engaged. Engage
auger control lever.
1.
1. Tire pressure not equal; should be 20 psi
(136
each side.
2
3
. Foreign matter blocking auger. STOP.engine and
REMOVE the key. DISCONNECT the spark plug
wire. Clear auger using a narrow board. See warning
in SAFETY RULES.
Excessive vibration.
Loose parts or damaged auger. STOP engine and
REMOVE the key. DISCONNECT the spark plug
wire. Tighten all hardware. Replace auger if neces-
sary. If vibration continues, see your dealer.
. Auger drive belt slipping. Check auger drive belt
1
0
| Categories | Simplicity Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Simplicity 1691411, Simplicity 1691413, Simplicity 1691414 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Simplicity, Snow Blower |
| Document File Type | |
| Publisher | simplicitymfg.com |
| Wikipedia's Page | Simplicity Outdoor |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)