Yard-Man 770-10278 993 Snow Blower Owners Manual by MTD

SHIFT ROD ADJUSTMENT
CARBURETOR ADJUSTMENT
To adjust the shift rod, remove the cotter pin which
secures  the  shift  rod  to  the  shift  lever.  For  proper
adjustment, refer to FINAL ADJUSTMENTS on page
6.
WARNING: If    any   adjustments    are
made to the engine while the engine is
running  (e.g.  carburetor),  keep  clear  of
all  moving  parts.  Be  careful  of  heated
surfaces and mufflers.
SKID SHOE ADJUSTMENT
Minor carburetor  adjustment may be  required to
compensate for differences in fuel, temperature,
altitude and load.
The space between the shave plate and the ground
can  be  adjusted.  Refer  to  Skid  Shoe   Adjustment
(See Figure 8) on page 6.
Refer  to  the  separate  engine  manual  packed  with
your unit for carburetor adjustment information.
NOTE: Failure
to
comply
with
suggested
maintenance and lubrication specifications on pages
10 and 11 will void warranty.
SECTION 8:  LUBRICATION
WHEELS
HEX SHAFT
Oil or spray lubricant into bearings at wheels at least
once  a  season.  Remove  wheels,   clean  and  coat
axles  with  a  multi-purpose  automotive  grease.  See
Figure 15.
Lubricate the hex shaft with a good all-weather multi-
purpose light grease at least once a season or after
every  25   hours   of  operation   (available  from   an
authorized  service  dealer  or  an  automotive  store.)
See Figure 15.
CHAINS AND SHIFTING MECHANISM
If
for
any
reason
your
transmission
was
disassembled  and  the   auger  cable  disconnected,
make  sure  when  reassembling  to  pass  the  cable
above  the   hex  shaft   before  reconnecting  to   the
auger actuator bracket.
Remove   lower  cover.   Oil   all   chains,   sprockets,
bearings,  the   hexagonal  shaft,   round  shaft,   and
shifting  mechanism  at  least   once  a  season.  Use
engine oil or a spray lubricant. Avoid getting oil on
rubber friction wheel and aluminum drive plate.
WARNING: When   following    instruc-
tions   in  separate   engine   manual  for
draining oil, be sure to protect frame to
avoid   oil  dripping   onto   transmission
parts.
CHUTE DIRECTIONAL CONTROL WORM
The worm gear on the chute directional crank should
be greased with multi-purpose automotive grease.
IMPELLER PULLEY
Trigger
The  impeller   pulley  should  be  lubricated   once  a
season. Refer to exploded view of parts, found in the
back of the book, for correct location.
Cables
Shift Arm
Assembly
Auger
Drive
Actuator
Bracket
Actuator
Bracket
AUGER SHAFT
Hex Nut
and
Remove auger bolts on auger shaft, see Figure 16.
Oil or spray lubricant inside shaft.
Cupped
Washers
ENGINE
Refer   to   engine   manual   for   engine   lubrication
instructions.
Hex
Shaft
Friction
Wheel
Figure 15  Viewed from the underside of snow
thrower
10
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, Yard Man Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 24 pages
Document TypeOwner's Manual
LanguageEnglish
Product Brand993 Series, Yard-Man, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website