7
Trouble-
Shooting
Problem
Engine fails to start
Cause
Remedy
1. Choke not in ON position.
1. Move choke to ON position.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
4. Prime engine as instructed in
2.
3.
4.
Spark plug wire disconnected.
Fuel tank empty or stale fuel.
Engine not primed.
“
Operating Your Snow Thrower”.
5.
6.
7.
Clean, adjust gap, or replace.
Clean fuel line.
5
. Faulty spark plug.
Blocked fuel line.
Safety key not in ignition on engine.
Fuel shut-ff valve closed. (If Equipped)
6.
7.
Insert key fully into the switch.
Open fuel shut-off valve.
8.
8.
Engine runs erratic
Engine overheats
1. Unit running on CHOKE.
1. Move choke lever to OFF position.
2. Cleanfresh gasoline.fuel line; fill tank with clean,
3. Dfrerasihnffuueell. tank. Refill with
2. Blocked fuel line or stale fuel.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
NOTE: This section
addresses minor
service issues. For
further details,
4.
Contact Service Center.
contact customer
assistance.
1. Carburetor not adjusted properly.
Loose parts or damaged auger.
1. Contact Service Center.
Excessive
Vibration
1.
1. Stop engine immediately and
disconnect spark plug wire. Tighten
all bolts and nuts. If vibration
continues, have unit serviced by a
Service Center.
Loss of power
1. Spark plug wire loose.
1. Connectwire. and tighten spark plug
2
3
. Gas cap vent hole plugged.
. Exhaust port plugged.
2. Remove ice and snow from gas
cap. Be certain vent hole is clear.
3. Contact Service Center.
toUnitpropelfails itself
1. Dmreivnet.control cable in need of adjust-
1. Adjust“Adjustments”.drive control cable. Refer to
2. Replace drive belt.
2
. Drive belt loose or damaged.
Unit fails
1
. Chute assembly clogged.
1. Stop engine immediately and
disconnect spark plug wire. Clean
chute assembly and inside of
auger housing with clean-out tool
or a stick.
to discharge snow
2
3
. Foreign object lodged in auger.
2. Stop engine immediately and
disconnect spark plug wire.
Remove object from auger with
clean-out tool or a stick.
. Ament.uger control cable in need of adjust-
Auger belt loose or damaged.
Shear pin(s) sheared.
3. Refer to “Auger Control Test” .
4.
5.
Refer to Maintenance section.
Replace with new shear pin(s).
4.
5.
15
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Yardworks Snow Blower Manuals |
|---|---|
| Tags | MTD 769-03250, MTD Snow Blower Manual, Yardworks 769-04164 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Yardworks, 769-04164, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(5 votes, average: 4.6 out of 5)
Lawn and Garden readers have rated Yardworks 769-04164 Snow Blower Owners Manual by MTD 4.6 out of 5.0 based on 5 product reviews. amazing website to obtain my manual
I'm always amazed at what you can find on the internet. This is the exact manual that I was looking for. Now I have a complete list of parts for my snow blower. This web site worked great and and the PDF downloaded and printed perfectly.
Thank you very much.
pretty good site to get in to download the manual
pretty good site to get in to download the manual
I am looking for the Separate Engine Manual mensioned on page 9 of the Operator’s Manual of my Snow Thrower model 769-04164 – Can anyone help me?
I am looking for the Separate Engine Manual mensioned on page 9 of the Yardwors Operator’s Manual of my Snow Thrower model 31AM33BE515 Can anyone help me?