5
Gas and Oil Fill-up
Engines with Electric Starters
WARNING: The electric starter is
•
Service the engine with gasoline and oil as instructed
in the separate engine manual packed with your
snowthrower. Read instructions carefully.
equipped with a grounded three-wire
power cord and plug, and is designed
to operate on 120 volt AC household
current. It must be used with a prop-
erly grounded three-prong receptacle
at all times to avoid the possibility of
electric shock. Follow all instructions
carefully prior to operating the electric
starter.
WARNING: Never fill fuel tank indoors.
Never fill fuel tank with engine running
or while engine is hot. Do not smoke
when filling fuel tank.
Operation
•
Make certain the auger and drive control bails are in
the disengaged (released) position.
Starting the Engine
WARNING: DO NOT use electric starter
WARNING: Always keep hands and
in rain.
feet clear of moving parts. Do not use
a pressurized starting fluid. Vapors are
flammable.
WARNING
1
.
Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are unsure. If you have a grounded three-prong
receptacle, proceed as follows. If you do not have
the proper house wiring, DO NOT use the electric
starter under any conditions.
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power until
it reaches operating temperatures.
2
3
.
.
Insert ignition key fully into slot. Make sure it snaps
into place. DO NOT turn ignition key. The engine
cannot start unless the key is inserted into
ignition switch.
Engines with Starter Handle (non-electric
start)
Use extreme care
when handling
running.IMPORTANT: Do not pull the starter handle with engine
Plug the extension cord into the electric switch box
located on the engine. Plug the other end of exten-
sion cord into a three-prong 120-volt, grounded, AC
outlet in a well-ventilated area.
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive.Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
1
.
Insert ignition key fully into slot. Make sure it snaps
into place. DO NOT turn ignition key. The engine
cannot start unless the key is inserted into ignition
switch.
4. Move throttle control to FAST (rabbit) position.
5. Move choke to the ON position (cold engine start).
If engine is warm, place choke in OFF position.
2
3
.
.
Move throttle control to FAST (rabbit) position.
Move choke to the ON position (cold engine start). If 6. Push primer three to five (3-5) times, making sure
engine is warm, place choke in OFF position.
Push primer three to five (3-5) times, making sure
to cover vent hole when pushing. If engine is warm,
push primer only once. Always cover vent hole when
pushing. Cool weather may require priming to be
repeated.
to cover vent hole when pushing. If engine is warm,
push primer only once. Always cover vent hole
when pushing. Cool weather may require priming
to be repeated.
4.
7. Push starter button to start engine. Once the
engine starts, immediately release starter button.
Electric starter is equipped with thermal overload
protection; system will temporarily shut-down to
allow starter to cool if electric starter becomes
overloaded.
5
.
.
Pull gently on the starter handle until it begins to
resist, then pull quickly and forcefully to overcome
the compression. Do not release the handle and al-
low it to snap back. Return rope SLOWLY to original
position. If required, repeat this step.
If your home’s wir-
ing system is not a
three-wire grounded
system, do not use
this electric starter
under any conditions.
8. As the engine warms, slowly rotate the choke
control to OFF position. If the engine falters, restart
engine and run with choke at half-choke position
for a short period of time, and then slowly rotate the
choke into OFF position.
6
As the engine warms, slowly rotate the choke control
to OFF position. If the engine falters, restart engine
and run with choke at half-choke position for a short
period of time, and then slowly rotate the choke into
OFF position.
9. After engine is running, disconnect power cord
from electric starter. When disconnecting, always
unplug the end at the wall outlet before unplugging
the opposite end from the engine.
If your home
electrical system
is grounded, but a
three-hole receptacle
is not available, do
not use your snow
thrower’s electric
starter.
9
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Yardworks Snow Blower Manuals |
|---|---|
| Tags | MTD 769-03250, MTD Snow Blower Manual, Yardworks 769-04164 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Yardworks, 769-04164, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(5 votes, average: 4.6 out of 5)
Lawn and Garden readers have rated Yardworks 769-04164 Snow Blower Owners Manual by MTD 4.6 out of 5.0 based on 5 product reviews. amazing website to obtain my manual
I'm always amazed at what you can find on the internet. This is the exact manual that I was looking for. Now I have a complete list of parts for my snow blower. This web site worked great and and the PDF downloaded and printed perfectly.
Thank you very much.
pretty good site to get in to download the manual
pretty good site to get in to download the manual
I am looking for the Separate Engine Manual mensioned on page 9 of the Operator’s Manual of my Snow Thrower model 769-04164 – Can anyone help me?
I am looking for the Separate Engine Manual mensioned on page 9 of the Yardwors Operator’s Manual of my Snow Thrower model 31AM33BE515 Can anyone help me?