3
Setup And
Adjustment
IMPORTANT: This unit is shipped WITH OIL and
WITHOUT GASOLINE. After assembly refer to
separate engine manual for proper fuel and engine oil
recommendations.
NOTE: Reference to right hand or left hand side of
machine are observed from the operating position.
NOTE: This Operator’s Manual covers several
models. Snow thrower features vary by model. Not all
features discussed in this manual are applicable to all
snow thrower models.
Chute Handle
Setting Up The Handle
NOTE: Be aware of the three loosely fitted cable ties
attached to the lower handle that will be ustilizred later
to secure the cables.
Figure 1
WARNING
handle. See Figure 1.
WARNING: Do not lift the snow thrower by the chute
1.
2.
Loosen and remove the wing knob, saddle washer,
handle tab and carriage bolt on each side of the
lower handle. See Figure 2.
Slide one of the loosely fitted cable ties from the right
side of the lower handle up to the cross member
of the lower handle. Leave the second cable tie
in place on the right side of the lower handle. See
Figure 4. for reference.
Always stop engine,
disconnect spark
plug, and ground
against engine before
cleaning, lubricating
or doing any kind
of maintenance or
adjustments on your
machine.
3.
Lift the upper handle up and position it over the lower
handle, aligning the holes where the wing knobs
were removed. See Figure 3.
CAUTION: Be careful not to bend or kink the cable.
DO NOT LIFT
4. Insert the carriage bolt from the outside through a
handle tab, the upper and lower handles, a saddle
washer and into the wing knob . Repeat on the other
side.
MACHINE WITH
CHUTE HANDLE.
Figure 2
5.
Tighten the wing knobs on each side of the handle.
NOTE: Never replace
the auger shear pins
with standard pins.
Any damage to the
auger gearbox or other
components, as a reult
of doing so, will NOT
be covered by your
snow thrower’s war-
ranty.
See Figure 3.
NOTE: Make sure that the drive cable is routed parallel
to the left upper handle, then across the top of the lower
handle and finally parallel to the right lower handle. See
Figure 4.
6. Three cable ties have been used to loosely tie the
two control cables to the lower handle. Two of these
cable ties are on each arm, and third on the top
cross bar of the lower handle. Tighten these cable
ties to secure the cable to the lower handle. See
Figure 4.
Clean-Out Tool
Never use your hands
to clean snow and
ice from the chute
assembly or auger
housing..
This tool and the electric extension cord, if so equipped,
may be fastened with a cable tie to the rear of the auger
housing for shipping purposes. In that case, cut the
cable tie and remove the extension cord now.
Figure 3
6
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Yardworks Snow Blower Manuals |
|---|---|
| Tags | MTD 769-03250, MTD Snow Blower Manual, Yardworks 769-04164 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Yardworks, 769-04164, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(5 votes, average: 4.6 out of 5)
Lawn and Garden readers have rated Yardworks 769-04164 Snow Blower Owners Manual by MTD 4.6 out of 5.0 based on 5 product reviews. amazing website to obtain my manual
I'm always amazed at what you can find on the internet. This is the exact manual that I was looking for. Now I have a complete list of parts for my snow blower. This web site worked great and and the PDF downloaded and printed perfectly.
Thank you very much.
pretty good site to get in to download the manual
pretty good site to get in to download the manual
I am looking for the Separate Engine Manual mensioned on page 9 of the Operator’s Manual of my Snow Thrower model 769-04164 – Can anyone help me?
I am looking for the Separate Engine Manual mensioned on page 9 of the Yardwors Operator’s Manual of my Snow Thrower model 31AM33BE515 Can anyone help me?