Assembly
2.
Install speed selector rod into selector arm, add
one flat washer on the selector rod and secure
with cotter pin (Fig. 4).
Note:
Determine left and right sides of
snowthrower by standing in the normal
operating position.
Install Handle
Install Traction Rod
1.
Remove tie straps securing control rods to
handle.
1.
2.
Thread a flange nut (flange side down) onto
traction rod located on left handle (Fig. 5).
2.
Remove the axle pins from both wheels and
slide the wheels outward on the axle
approximately one inch to make clearance for
assembly of handles.
Thread a flange nut (flange side up) onto bottom
of traction control rod below loop in lower
traction rod (Fig. 5).
3.
Position left handle against side of unit, make
sure traction rod goes through loop in lower
traction rod (Fig. 5), align handle mount holes
with holes in side plate, and secure with two
capscrews and curved washers until finger tight
(Fig. 2).
3.
Adjust the two flange nuts up or down on the
traction control rod until the distance between
the top of the handgrip and the bottom of the
traction control lever#8 (Figs. 6 and 7) is
approximately 4 / inches. This is a
preliminary setting only. Tighten the two
flange nuts finger tight.
Note:
Concave side of curved washer goes
against outside of handle.
Repeat procedure on right side. Make sure handles
are at same height before tightening handle screws on
both sides of unit.
4.
Move speed selector (Fig. 6) into third gear.
4.
Reinstall the wheels. Note that there are two
holes in each end of the axle. Axle pins are
installed through holes in the wheel hub and
through inner hole of axle (Fig. 3).
Note:
If speed selector will not move into
third gear, an adjustment is necessary:
refer to Adjusting Speed Selector,
page 17. Make the adjustment before
continuing with assembly.
Note:
If snowthrower is to be equipped with
optional tire chains, wheels must be
pinned through outer axle holes.
5.
Slowly pull machine backward while slowly
depressing traction control lever toward handle.
Adjustment is correct when wheels stop turning
and the distance between the top of the handgrip
and the bottom of the traction control lever is
one to two inches (Fig. 7). Readjust the two
flange nuts, if necessary, to obtain this
dimension and then tighten the two flange nuts
securely.
Install Speed Selector Rod
1.
Pull speed selector arm (Fig. 4) to the fully “out”
position and move speed selector (Fig. 6) on
control panel to the R (REVERSE) position to
ease assembly.
8
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38062, Toro 622, Toro 9900001 |
| Model Number | 38062 |
| Model Year | 1999 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 9900001 - 9999999 |
| Product Name | Toro 622 38062 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 7 oz. (198gm) Lubriplate MAG-1 |
| Engine Motor Model # | HSK60-76011C |
| Engine Motor Size | 6 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(3 votes, average: 4.67 out of 5)
Lawn and Garden readers have rated Toro 622 38062 Snow Blower Operators Manual, 1999 4.7 out of 5.0 based on 3 product reviews. Fine snowblower, no complaints
Thank you very Much!!!!!!
5