Note:
If auger/impeller drive belt is replaced
with a new belt, adjust auger/impeller
drive linkage. Refer to steps 4–6 of
Install Auger/Impeller Drive Control
Linkage, page 9.
5.
6.
With drive assembly 1/8” from contacting roll
pin, tighten flange nuts securing speed selector
plate.
Shift speed selector to R (REVERSE) and back
torollthirdpin toandcheckdriveadjustment.assembly isIfmorespacethanbetween#/16 of
14.
Reinstall belt cover with (2) screws.
an inch (4.8 mm), repeat steps 2–4.
7.
Reassemble bottom cover with (4) screws.
Adjusting Traction Drive
If speed selector shifts properly but snowthrower does
not drive in reverse or forward speeds, an adjustment
may be required.
Replacing Spark Plug
Use a Champion RJ–19LM spark plug or equivalent.
Set air gap at 0.030” (0.76 mm). Check spark plug
yearly or every 100 operating hours. If electrodes in
center of plug are dark or have deteriorated, install a
new plug.
1.
Pull wire off spark plug and make sure it does
not contact the plug accidentally.
2.
Check adjustment per steps 5 and 6 of Install
Traction Rod, page 8. Make adjustments if
required.
1.
Clean area around spark plug so foreign matter
cannot fall into cylinder when plug is removed.
3.
If linkage is adjusted correctly and problem
persists, contact your local Authorized Toro
Service Dealer.
2.
Pull wire off spark plug (Fig. 29) and remove
plug from cylinder head.
IMPORTANT: A cracked, fouled or dirty
spark plug must be replaced. Do not sand
blast, scrape or clean electrodes because grit
may eventually release from the plug and fall
into the cylinder. The result will likely be
engine damage.
Adjusting Speed Selector
If there is slow or no ground speed in No.1 speed
selection, or speed selector cannot be moved into No.
3
speed selection, an adjustment of the speed selector
linkage is required.
3.
4.
Set air gap between electrodes of new spark plug
at 0.030” (0.76 mm) (Fig. 30). Next, install
spark plug incylinder head. Tighten plug to 15
ft–lb (20.4 N m).
1.
2.
3.
Pull wire off spark plug and make sure wire does
not contact plug accidentally.
Remove (4) screws securing bottom cover to
frame. Remove cover (Fig. 20).
Push the wire onto the spark plug (Fig. 29).
Loosen flange nuts securing selector plate to
control panel. This allows selector plate to move
freely for adjustment (Fig. 27).
Preparing Snowthrower For
Storage
4.
Shift speed selector to third gear and push down
on speed selector plate to move drive assembly
to the right. Drive assembly should be 1/8” from
roll pin; if not, slide selector plate (Fig. 27) until
1.
FUEL SYSTEM PREPARATION–
Note:
A fuel stabilizer/conditioner is most
effective when mixed with fresh
gasoline.
1/8”
dimension is correct (Fig. 28).
17
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38062, Toro 622, Toro 9900001 |
| Model Number | 38062 |
| Model Year | 1999 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 9900001 - 9999999 |
| Product Name | Toro 622 38062 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 7 oz. (198gm) Lubriplate MAG-1 |
| Engine Motor Model # | HSK60-76011C |
| Engine Motor Size | 6 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(3 votes, average: 4.67 out of 5)
Lawn and Garden readers have rated Toro 622 38062 Snow Blower Operators Manual, 1999 4.7 out of 5.0 based on 3 product reviews. Fine snowblower, no complaints
Thank you very Much!!!!!!
5