Poulan 2250 2450 2550 Chainsaw Owners Manual

S  If  the  brake  is  already   activated,  it  is
disengaged by pulling the front hand guard
back  toward  the front  handle  as  far  as
possible.
ON/STOP
Switch
S  When cutting with the saw,the chain brake
must be disengaged.
Primer
Bulb
Disengaged
Engaged
ON/STOP SWITCH
ON
STOP
CHOKE/FAST IDLE LEVER
(SIDE VIEW)
Braking function control
CAUTION:
The  chain  brake   must  be
checked  several  times  daily.  The  engine
must be running when performing this proce-
dure. This is the only instance when the saw
should be placed on the ground with the en-
gine running.
Choke/Fast
Idle Lever
OFF
FULL
Place the saw on firm ground.  Grip the rear
handle with your right hand and the front han-
dle with your left hand.  Apply full  throttle by
fully depressing the throttle trigger.  Activate
the  chain  brake by  turning  your  left  wrist
against  the  hand  guard  without  releasing
your grip around the front handle. The chain
should stop immediately.
STARTING A WARM ENGINE:
1.
Move ON/STOP switch  to the ON posi-
tion.
2.
Pull the choke/fast idle lever out to the full
extent, then push the lever back in com-
pletely (to the OFF position).
3.
4.
Slowly press the primer bulb 6 times.
Pull  the starter  rope  quickly  with your
right hand until the engine  starts.
Squeeze and release throttle trigger,  al-
lowing engine to idle.
Inertia activating function control
5.
WARNING:
When performing  the
following  procedure,   the  engine  must  be
DIFFICULT STARTING (or starting a
turned off.
flooded engine):
Grip the rear handle with your right hand and
the front handle with your left hand. Hold the
chain saw approximately 14! (35 cm) above
a stump or  other wooden surface.  Release
your grip  on  the front  handle  and use  the
weight of the  saw to let the top of the guide
bar  fall   forward  and  contact   the  stump.
When the  tip of the  bar hits the  stump, the
brake should activate.
The engine  may be flooded  with  too much
fuel if it has not started  after 10 pulls.
Flooded engines  can be cleared  of excess
fuel  by following  the  warm engine  starting
procedure  listed  above.    Insure  the  ON/
STOP switch is in the ON position.
Starting could require pulling the starter rope
handle many times depending on how badly
the unit is flooded. If engine fails to start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
CUTTING METHODS
CHAIN BRAKE
IMPORTANT POINTS
S  Check chain tension  before first use  and
after 1  minute of  operation.  See  CHAIN
TENSION in the ASSEMBLY section.
WARNING:
If the  brake  band is
worn too  thin it may  break when  the chain
brake is triggered. With abroken brake band,
the chain brake  will not stop the chain.  The
chain brake should be replaced by an autho-
rized service dealer if any part is worn to less
than 0.020!  (0.5  mm) thick.   Repairs on  a
chain brake  should  be made by  an autho-
rized  service dealer.  Take your  unit to  the
place of  purchase if purchased  from a ser-
vicing  dealer, or  to the  nearest authorized
master service dealer.
S
S
S
Cut wood only. Do not cut metal, plastics,
masonry,  non-wood   building   materials,
etc.
Stop the saw if the chain strikes  a foreign
object.  Inspect  the saw and repair  or re-
place parts as necessary.
Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull achain
and thus  increase the  possibility of  kick-
back.
S  This saw is equipped with  a chain brake.
The brake is designed to stop  the chain if
kickback occurs.
S  Practice cutting a few small logs using the
following techniques to get the “feel” of us-
ing  your saw  before  you begin  a  major
sawing operation.
S  The
inertia--activated
chain   brake   is
activated if the front hand guard is pushed
forward,  either   manually  (by   hand)  or
automatically (by sudden  movement).
S
Squeeze the  throttle trigger  and allow
the engine  to reach  full  speed before
cutting.
10
Product Specification
CategoriesChainsaw Manuals, Poulan Chainsaw Manuals
Tags, ,
Model Year2002
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 17 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(2 votes, average: 4 out of 4)
Lawn and Garden readers have rated Poulan 2250 2450 2550 Chainsaw Owners Manual 4.0 out of 4.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Poulan 2250 2450 2550 Chainsaw Owners Manual SKU UPC Model
Gerald DeFillippo on Nov 30, 2015. Download Manual

Easy and quick, no bullshit, thanks....


Gerald DeFillippo on Nov 30, 2015. Download Manual

Easy and quick, no bullshit, thanks....


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website