S If the brake is already activated, it is
disengagedby pullingthefronthandguard
back toward the front handle as far as
possible.
thecut,damagetothebar,chain,oren-
gine can result.
S
S
Release the throttle trigger as soon as
the cut is completed, allowing the en-
gine to idle. If you run the saw at full
throttlewithoutacuttingload,unneces-
sary wear can occur to the chain, bar,
and engine. It is recommended that
the engine not be operated for lon-
ger than 30 seconds at full throttle.
To avoid losing control when cut is com-
plete, do not put pressure on saw at end
of cut.
S Whencuttingwiththesaw,thechainbrake
must be disengaged.
Disengaged
Engaged
S Stop the engine before setting the saw
down after cutting.
TREE FELLING TECHNIQUES
Braking function control
The chain brake must be
checked several times daily. The engine
mustberunningwhenperformingthisproce-
dure. This is theonly instancewhen thesaw
should be placed on the ground with the en-
gine running.
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
CAUTION:
WARNING: Check forbrokenordead
branches which can fall while cutting causing
serious injury. Do not cut near buildings or
electrical wires if you do not know the direction
of tree fall, nor cut at night since you will not be
aletoseewell,nor duringbadweather suchas
rain, snow, or strong winds, etc. If the tree
makes contact with any utility line, the utility
company should be notified immediately.
S Carefullyplanyour sawingoperationinad-
vance.
S Cleartheworkarea. Youneedacleararea
allaroundthetreeso youcan havesecure
footing.
S The chain saw operator should keep on
the uphill side of the terrain as the tree is
likelytorollor slidedownhillafteritisfelled.
S Study the natural conditions that can cause
the tree to fall in a particular direction.
Natural conditions that can cause a tree to
fall in a particular direction include:
Inertia activating function control
WARNING: When performing the
following procedure, the engine must be
turned off.
Grip therear handlewith your right handand
the front handle with your left hand. Holdthe
chainsaw approximately 14″ (35 cm) above
a stump or other wooden surface. Release
your grip on the front handle and use the
weightofthesaw toletthetipoftheguidebar
fallforwardandcontactthestump. Whenthe
tipofthebar hits thestump,the brakeshould
activate.
S
S
The wind direction and speed.
The lean of the tree. The lean of a tree
might not be apparent due to uneven or
slopingterrain. Useaplumb or level tode-
termine the direction of tree lean.
S
S
Weight and branches on one side.
Surrounding trees and obstacles.
Look for decay and rot. If thetrunk is rotted,
OPERATING TIPS
it can snap and fall toward the
operator.
S Check chain tension before first use and
after 1 minute of operation. See CHAIN
TENSION in the ASSEMBLY section.
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary.
Check for broken or dead branches which
can fall on you while cutting.
Make sure there is enough room for the treeto
fall. Maintain a distance of
2-1/2
tree lengths
from the nearest person or other objects. En-
gine noise can drown out a warning call.
Remove dirt, stones, loose bark, nails, sta-
ples,andwirefromthetreewherecuts areto
be made.
Plana clear retreat pathto therear anddiag-
onal to the line of fall.
S Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull a chain
andthus increasethepossibility ofkickback.
S Practice cutting a few small logs using the
following techniques to get the“feel” ofus-
ing your saw before you begin a major
sawing operation.
Plan a clear retreat path
S
S
S
S
Squeeze the throttle trigger and allow the
engine to reach full speed before cutting.
saw frame
Begin cutting with the
against the log.
Direction of Fall
Keep the engine at full speed the entire
time you are cutting.
Allowthechaintocutforyou.Exertonly
light downward pressure. If you force
45_
11
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro PPB3416, Poulan Pro PPB4218 |
| Model Year | 2005 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)