Poulan Pro PPB3416 PPB4218 Chainsaw Owners Manual

6.
Reinstall spark arresting screen, exhaust
outlet cover,and nut.Tighten nutsecurely.
CHAIN ADJUSTMENT
See CHAIN TENSION in ASSEMBLY sec-
tion.
REPLACE SPARK PLUG
The  spark plug  should  be replaced  each
year to ensure the engine starts easier and
runs better. Ignition timing is fixed and non-
adjustable.
CHAIN SHARPENING
Chain sharpening is a complicated task and
requires special tools. We recommend that
you refer chain sharpening to a professional
chain sharpener.
1.
2.
3.
4.
Loosen 3 screws on cylinder cover.
Remove the cylinder cover.
Pull off the spark plug boot.
Remove spark  plug from  cylinder and
discard.
CARBURETOR ADJUSTMENT
WARNING: Thechainwillbemoving
during most  of this  procedure. Wear  your
protective equipment and observe all safety
precautions.Thechainmustnotmoveatidle
speed.
The carburetor has been carefully set at the
factory. Adjustments  may  be necessary  if
you notice any of the following conditions:
S  Chain moves at idle. See IDLE SPEED--T
adjusting procedure.
S  Saw will not idle. See IDLE SPEED--T ad-
justing procedure.
5.
Replace with Champion RCJ--7Y spark
plug and tighten securely with a 3/ inch
4
(19
mm) socket wrench. Spark pluggap
should be 0.025 inch (0,6 mm).
Reinstall the spark plug boot.
the   cylinder  cover   and  3
screws. Tighten securely.
6.
7.
Reinstall
Cylinder
Cover
Idle Speed--T
Allow engine to idle. If the chain moves, idle is
toofast. Iftheenginestalls,idleis    tooslow. Ad-
just  speed  until  engine runs  without  chain
movement (idle  too fast)  or stalling (idle  too
slow). The idle speed screw is located  in the
area above the primer bulb and is labeled T.
S  Turn idle screw (T) clockwise to increase
engine speed.
Spark
Plug Boot
S  Turn idle screw  (T) counterclockwise  to
decrease engine speed.
Spark
Plug
If you require further assistance or are unsure
about performing this procedure, contact your
authorized service dealer or call our customer
assistance help line at 1--800--554--6723.
REPLACE FUEL FILTER
To replace fuel filter, drain your unit by run-
ning it dry of fuel.  Remove fuel cap and its
connected retainer from tank. Pull filter from
tank and remove from line. Replace and re-
assemble.
STORAGE
S  Store in a clean dry area.
S  Lightly  oil external  metal  surfaces  and
guide bar.
S  Oil the chain and wrap it in heavy paper or
cloth.
WARNING:  Perform  the  following
steps after each use:
S  Allow the engine to cool, and secure  the
unit before storing or transporting.
S  Store chain saw and fuel  in a well venti-
lated area where fuelvapors cannotreach
sparks or openflames from water heaters,
electric motors or switches, furnaces, etc.
S  Store chain saw with  all guards in place
and position chain saw so that any sharp
object cannot accidentally cause injury.
S  Store chain saw well out  of the reach of
children.
SEASONAL STORAGE
Prepareyourunitfor  storageattheendofthe
season or if it will not be used for 30 days or
more.
FUEL SYSTEM
Under FUELING  ENGINE in  the OPERA-
TION section of this manual, see message
labeled IMPORTANT regarding  the use of
gasohol in your chain saw.
Fuel stabilizer is anacceptable alternativein
minimizing the formation of fuel gum depos-
its duringstorage.Addstabilizer  to thegaso-
line in the fuel tank or fuel storage container.
Follow the mix instructions found onstabiliz-
er containers. Run engine at least 5 minutes
after adding stabilizer.
Poulan/Weed Eater 40:1, 2-cycle engine oil
(air cooled) is blended with fuel stabilizer. If
youdonotusethisoil,youcanaddafuelsta-
bilizer to your fuel tank.
If your chain saw is to be stored for a period
of time:
S  Clean saw thoroughly before storage.
16
Product Specification
CategoriesChainsaw Manuals, Poulan Pro Chainsaw Manuals
Tags,
Model Year2005
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 19 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website