running the auger/impeller, push down on the handles
to raise the front of the snowthrower a few inches
(centimeters) off the pavement. Then lift the handles
quickly to bump the front of the snowthrower on the
pavement. Repeat if necessary until a stream of snow
comes out the discharge chute.
•
If you cannot unclog the discharge chute by bumping
the front of the snowthrower, stop the engine, wait
for all moving parts to stop, and use a stick; never
use your hand.
Important: Unclogging the discharge chute
by bumping the front of the snowthrower on the
pavement may cause the skids to move. Adjust the
skids and tighten the skid bolts securely.
PreventingFreeze-up
Figure32
•
In snowy and cold conditions, some controls and
moving parts may freeze. Do not use excessive force
when trying to operate frozen controls. If you have
difficulty operating any control or part, start the engine
and let it run for a few minutes.
•
If the chute does not move, refer to Adjusting the
Discharge Chute Latch.
•
If the chute does not turn as far to the left as it does to
the right, ensure that the cable is routed to the inside of
the handles. Refer to Installing the Upper Handle.
•
After using the snowthrower, let the engine run for
a few minutes to prevent moving parts from freezing.
Engage the auger/impeller to clear any remaining snow
from inside the housing. Rotate the Quick Stick to
prevent it from freezing. Stop the engine, wait for all
moving parts to stop, and remove all ice and snow from
the snowthrower.
•
If the chute does not lock into place when you release
the trigger cap, refer to Adjusting the Discharge Chute
Latch.
MovingtheChuteDeector
Hold the blue trigger cap down and move the Quick Stick
forward to lower the chute deflector; move it rearward to
raise the chute deflector (Figure 33).
•
With the engine off, pull the recoil starter handle several
times to prevent the recoil starter from freezing up.
Figure33
Unclogging theDischarge
Chute
If the auger/impeller is running but there is no snow
coming out of the discharge chute, the discharge chute may
be clogged.
•
To unclog the discharge chute, stay in the operating
position and release the left hand (traction) lever. While
13
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38622, Toro Power Max 828LE |
| Model Number | 38622 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 260000001 - 260999999 |
| Product Name | Toro Power Max 826 LE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | LH318SA-156563H |
| Engine Motor Size | 318cc |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)