4.
5.
Move the speed selector lever to Position R2.
Dip your finger in automotive engine oil and lightly
lubricate hex shaft.
6.
7.
8.
Move the speed selector lever to Position 6.
Lubricate the other end of the hex shaft.
Move the speed selector lever forward and rearward
a few times.
Figure47
9.
Install the back cover and return the snowthrower to
the operating position.
2. Loosen the bolt on the cable clamp (Figure 48).
InspectingandReplacingthe
SparkPlug
Use a Champion RJ-19LM or equivalent spark plug. Check
and gap the spark yearly, and replace the plug if necessary.
1.
2.
3.
Clean around the base of the spark plug.
Remove the spark plug.
Examine the spark plug and replace it if it is cracked,
fouled, dirty, or if the electrodes are worn.
Figure48
Important: Do not clean the electrodes because
grit could enter the cylinder and damage the
engine.
1.
Cableconduit
2.
Cableclamp
3.
Grasp the cable conduit and move it toward the front of
the machine until the discharge chute latch fully engages
the gear teeth (Figure 48 and Figure 49).
4.
Set the gap between the electrodes on the spark plug at
0.030
inch (0.76 mm) (Figure 46).
Figure46
1.
0.030inch(0.76mm)
5.
Install the spark plug by hand and then torque it to 15
ft-lb (20.4 N·m).
Figure49
Note: If you do not have a torque wrench, tighten
1.
Dischargechutelatch
2.
Gearteeth
the plug firmly.
Note: The latch is spring loaded and will naturally
move into the teeth of the gear (Figure 49).
AdjustingtheDischargeChute
Latch
4.
Remove any slack in the cable by pulling the cable
conduit rearward.
5.
6.
Tighten the bolt on the cable clamp.
Install and secure the gear cover.
If the discharge chute does not lock into the desired
position or does not unlock so that you can move it to
another position, adjust the discharge chute latch.
ReplacingtheDriveBelts
1.
Remove the fastener on the gear cover (Figure 47), lift
the front of the cover up, and slide it back and out of
the way.
If the auger/impeller drive belt or the traction drive belt
becomes worn, oil-soaked, or otherwise damaged, go to
18
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38622, Toro Power Max 828LE |
| Model Number | 38622 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 260000001 - 260999999 |
| Product Name | Toro Power Max 826 LE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | LH318SA-156563H |
| Engine Motor Size | 318cc |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)