Important: Refer to your engine operator’s manual for additional maintenance procedures. For engine
adjustments, repairs, or warranty service not covered in this manual, contact an Authorized Tecumseh Servicing
Dealer.
PreparingforMaintenance
1. Check the tire pressure. Refer to Checking the Tire
Pressure.
1.
2.
3.
Move the snowthrower to a level surface.
2.
Loosen the nuts that secure both skids to the auger
sides until the skids slide up and down easily (Figure 36).
Stop the engine and wait for all moving parts to stop.
Disconnect the spark plug wire (Figure 34).
Figure36
Figure34
3. Support the side plates so that they are at least 1/2 inch
cm) above a level surface.
(1.3
CheckingtheEngineOilLevel
Important: The auger blades must be supported
above the ground by the skids.
Each time before using the snowthrower, check the oil level
in the engine crankcase.
4.
Ensure that the scraper is 1/8 inch (3 mm) above and
parallel to a level surface.
1.
Remove the dipstick, wipe it clean, then fully install the
dipstick.
Note: If the pavement is cracked, rough, or uneven,
adjust the skids to raise the scraper. For gravel
surfaces, adjust the skids further down to prevent the
snowthrower from picking up rocks.
2.
Remove the dipstick and check the oil level (Figure 35).
If the oil level is below the Add mark on the dipstick,
add oil. Refer to Filling the Engine with Oil.
5.
6.
Move the skids down until they are even with the
ground.
Firmly tighten the nuts that secure both skids to the
auger sides.
Note: To quickly adjust the skids if they loosen,
support the scraper 1/8 inch (3 mm) off the pavement,
then adjust the skids down to the pavement.
Note: If the skids become excessively worn, you can
turn them over and set the unused side toward the
pavement.
CheckingandAdjustingthe
TractionCable
Figure35
Check and adjust the traction cable after the first 2 operating
hours, then yearly thereafter. If the snowthrower does not
drive in the forward or reverse speeds or it drives when you
release the traction lever, adjust the traction cable.
CheckingandAdjustingthe
SkidsandScraper
Check the skids and the scraper to ensure that the auger
does not contact the paved or gravel surface. Adjust the
skids and the scraper as needed to compensate for wear.
With the traction lever disengaged, check the pin in the
elongated slot in the left side of the snowthrower above
the tire. There should be a gap of 1/32 to 1/16 inch (1 to
15
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38622, Toro Power Max 828LE |
| Model Number | 38622 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 260000001 - 260999999 |
| Product Name | Toro Power Max 826 LE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | LH318SA-156563H |
| Engine Motor Size | 318cc |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)