8.
9.
Tighten the jam nut.
Insert the 2 screws you previously removed on the belt
cover.
10.
If the auger/impeller cable is properly adjusted but a
problem remains, contact an Authorized Service Dealer.
Figure43
1.
Oildraincap
CheckingtheAugerGearbox
OilLevel
2.
3.
Slide an oil drain pan under the drain extension and
remove the oil drain cap.
Drain the oil.
Check the auger gearbox oil yearly and add oil if necessary.
Note: Dispose of the used oil properly at a local
recycling center.
1.
2.
Move the snowthrower to a level surface.
Clean the area around the pipe plug (Figure 42).
4.
5.
Install the oil drain cap.
Fill the crankcase with oil. Refer to Filling the Engine
Crankcase with Oil.
LubricatingtheHexShaft
Lightly lubricate the hex shaft yearly with automotive engine
oil (Figure 44).
Figure42
3.
4.
Remove the pipe plug from the gearbox.
Check the oil level in the gearbox. The oil should be at
the point of overflowing at the filler opening.
5.
If the oil level is low, add GL-5 or GL-6, SAE 85-95
EP transmission oil to the gearbox until the point of
overflow.
Figure44
Note: Do not use synthetic oil.
1.
2.
Hexshaft
Aluminumfrictionplate
3.
Rubberwheel
6.
Install the pipe plug in the gearbox.
Important: Do not get oil on the rubber wheel or
the aluminum friction drive plate because the traction
drive will slip (Figure 44).
ChangingtheEngineOil
Change the engine oil after the first 2 operating hours, then
yearly thereafter. If possible, run the engine just before
changing the oil because warm oil flows better and carries
more contaminants.
1.
2.
Drain the gasoline from the fuel tank.
Tip the snowthrower forward onto its auger housing
and block it so that it cannot fall.
3.
Remove the back cover (Figure 45).
Max. fill: 26 oz. (0.77 l), type: automotive detergent oil with
an API service classification of SF, SG, SH, SJ, SL, or higher.
•
•
For temperatures above 32°F (0°C), use SAE 30W.
For temperatures between 0°F and 32°F (-18°C to 0°C),
use SAE 5W30 or SAE 10W.
•
For air temperatures below 0°F (-18°C), use SAE 0W30.
Clean the area around the oil drain cap (Figure 43).
Figure45
1.
1.
Backcover
17
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38622, Toro Power Max 828LE |
| Model Number | 38622 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 260000001 - 260999999 |
| Product Name | Toro Power Max 826 LE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | LH318SA-156563H |
| Engine Motor Size | 318cc |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)