MAINTENANCE
General
- L = Low speed jet
-
-
H = High speed jet
The user must only carry out the maintenance and
service work described in this manual.
T = Idle adjustment screw
T
H
IMPORTANT! Any maintenance other than that
described in this manual must be carried out by your
servicing dealer (retailer).
Carburettor adjustment
L
The carburettor can be designed in different ways,
depending on existing environmental and emissions
legislation. Some chain saws are equipped with
movement limiters on the carburettor’s adjuster screws.
These limit the adjustment possibilities to a maximum of
a 1/2 turn.
•
•
The L and H-jets are used to adjust the supply of fuel
to match the rate that air is admitted, which is
controlled with the throttle. If they are screwed
clockwise the air/fuel ratio becomes leaner (less fuel)
and if they are turned anti-clockwise the ratio
becomes richer (more fuel). A lean mixture gives a
higher engine speed and a rich mixture gives a lower
engine speed.
The T-screw regulates the throttle setting at idle
speed. If the T-screw is turned clockwise this gives a
higher idle speed; turning it anti-clockwise gives a
lower idle speed.
Basic settings and running in
When your chain saw is equipped with a carburettor that
features movement limiters, the carburettor should be
adjusted according to the instructions under the heading
Carburettor with movement limiters.
The basic carburettor settings are adjusted during testing
at the factory.Avoid running at a too high speed during the
first 10 hours.
CAUTION! If the chain rotates while idling theT-screw
must be turned anti-clockwise until the chain stops.
Rec. idle speed: 2700 rpm
Carburettor with movement
limiters
Fine adjustment
When the machine has been ”run-in” the carburettor
should be finely adjusted.The fine adjustment should be
carried out by a qualified person. First adjust the L-jet,
then the idling screw T and then the H-jet.
Changing the type of fuel
Fine tuning may be required if the chain saw, after
changing the type of fuel, performs differently with regard
to starting, acceleration, maximum speed, etc.
Conditions
Your Jonsered product has been designed and
manufactured to specifications that reduce harmful
exhaust fumes.
•
Before any adjustments are made the air filter should
be clean and the cylinder cover fitted. Adjusting the
carburettor while a dirty air filter is in use will result in
a leaner mixture next time the filter is cleaned. This
can give rise to serious engine damage.
Function
•
The carburettor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the
carburettor.The air/fuel mixture is adjustable. Correct
adjustment is essential to get the best performance
from the machine.
•
•
•
Do not attempt to adjust the L and H jets beyond either
stop as this could cause damage.
Now start the machine according to the starting
instructions and let it warm up for 10 minutes.
Place the machine on a flat surface so that the bar
points away from you and so that the bar and chain do
not come into contact with the surface or other
objects.
•
Adjusting the carburettor means that the engine is
adapted to local operating conditions, e.g. climate,
altitude, petrol and the type of 2-stroke oil.
•
The carburettor has three adjustment controls:
28
– English
| Categories | Chainsaw Manuals, Husqvarna Chainsaw Manuals |
|---|---|
| Tags | Husqvarna CS2166, Husqvarna CS2172WH |
| Model Year | 2009, 2010, 2011 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Product Brand | Husqvarna, Chainsaw |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)