Toro 522 Power Throw 38605 Snow Blower Operators Manual, 2009

5.
Installing the Chute Control
Rod
Chute control rod assembly (rod and bracket, worm
gear, and bracket)
1
1
1
1
2
Carriage bolt
Belleville washer
Hex head bolt
Locknut
Procedure
1.
Assemble the chute control bracket and rod to the
left side of the handle with the bolt and the locknut
as shown in Figure 10.
Figure 9
1.
2.
Handgrip
3.
4.
1 to 2 inches (3 to 5 cm)
5 inches (12.7 cm)
Auger/impeller control
lever
Note: The  distance should be approximately 5
inches (12.7 cm).
4.
Press the auger/impeller drive control lever slowly
toward the handgrip.
Figure 10
1.
Chute control bracket and
rod
2.   Hex head bolt and locknut
Note: The amount of force needed to compress the
lever increases noticeably when you remove the slack
from the auger/impeller drive belt (approximately
Note: Do not tighten the locknut.
1/2
of the lever movement). The  adjustment is
correct when the force begins to increase and the
distance between the top of the handgrip and the
bottom of the auger/impeller drive control lever is 1
to 2 inches (3 to 5 cm) as shown in Figure 9.
2.
Apply No. 2 general purpose grease to the worm
gear (Figure 11).
Note: If the force does not noticeably increase,
remove the belt cover (refer to step 2 of Replacing
the Traction Drive Belt in Maintenance) and measure
2
inches (5 cm) above the handgrip at the point
where you remove the slack from the auger/impeller
drive belt.
5.
To adjust the distance:
A.  Remove the clevis pin.
B.  Loosen the jam nut.
C.  Thread the clevis up or down to increase or
decrease the distance between the top of the
handgrip and the bottom of the auger/impeller
drive control lever (Figure 8).
Figure 11
1.
Worm gear
Bracket
3.
4.
Mounting flange
2.
Carriage bolt, Belleville
washer, and locknut
6.
7.
When the adjustment is correct, install the clevis pin
and secure it in place with the cotter pin (Figure 8).
Tighten the jam nut to secure the clevis (Figure 8).
10
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags,
Model Number38605
Model Year2009
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOperator's Manual
LanguageEnglish
Serial Number290000001 - 290999999
Product NameToro 522 Power Throw Snowthrower
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Product SeriesSnowthrower, Two Stage Small Frame
Swath22 inch
DischargeTwo Stage
Engine ManufacturerTecumseh
Engine Oil Type21 oz. (.62l) 5w-30 or 10w / API SH or higher
Gearbox LubricantAuger 5 oz. Lubriplate Mag 1 grease
Engine Motor Model #LH195SA-67435V
Engine Motor Size195cc
Engine Motor Type4 Cycle, 4 Cycle CARB3, EPA2
Transmission Speed3 Forward/1 Reverse
Transmission TypeFriction Disc
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 522 Power Throw 38605 Snow Blower Operators Manual, 2009 4.0 out of 4.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 522 Power Throw 38605 Snow Blower Operators Manual, 2009 SKU UPC Model
Charles per on Jan 09, 2015. so far so good one I get it started

Having trouble getting it started but once it gets going is awesome


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website