Toro 522 Power Throw 38605 Snow Blower Operators Manual, 2009

4.
5.
Open the fuel shutoff valve and allow the fuel to
drain out of the fuel tank into the drain pan.
11. Pull the recoil starter slowly to distribute the oil on
the inside of the cylinder.
Install the fuel line onto the fuel shutoff valve and
secure it with a hose clamp.
12. Lubricate the snowthrower. Refer to Lubricating the
Snowthrower.
6.
7.
Connect the wire to the spark plug.
13. Clean the snowthrower.
Start the snowthrower and run the engine until it
stops. Repeat this step 2 more times to ensure that
the fuel tank and the carburetor are empty.
14. Touch up chipped surfaces with paint available
from an Authorized Service Dealer. Sand affected
areas before painting, and use a rust preventative to
prevent the metal parts from rusting.
Storage
15. Tighten any loose fasteners. Repair or replace any
damaged parts.
16.
Cover the snowthrower and store it in a clean, dry
place out of the reach of children. Allow the engine
to cool before storing it in any enclosure.
Gasoline vapors can explode.
Do not store gasoline more than 30 days.
Removing the Snowthrower
from Storage
Do not store the  snowthrower in an
enclosure near an open flame.
1.
Remove the spark plug and spin the engine rapidly
using the starter to blow the excess oil from the
cylinder.
Allow the engine to cool before storing it.
Preparing the Snowthrower
for Storage
2.
Install the spark plug by hand and then torque it to
15
ft-lb (20.4 N-m).
3.
4.
Connect the spark plug wire.
1.
2.
3.
On the last refueling of the year, add fuel stabilizer
to fresh fuel as directed by the engine manufacturer.
Perform the annual maintenance procedures as given
in the Recommended Maintenance Schedule.
Run the engine for 10 minutes to distribute the
conditioned fuel through the fuel system.
Stop the engine, allow it to cool, and drain the
fuel tank or run the engine until it stops. Refer to
Emptying the Fuel Tank.
4.
5.
Start the engine and run it until it stops.
Choke or prime the engine, start it a third time, and
run the engine until it will not start.
6.
Dispose of unused fuel properly. Recycle it according
to local codes, or use it in your automobile.
Note: Do not store stabilized gasoline for more
than 90 days.
7.
While the engine is still warm, change the engine oil.
Refer to Changing the Engine Oil.
8.
Remove the spark plug.
9.
Squirt 2 teaspoons of oil into the spark plug hole.
Install the spark plug by hand and then torque it to
10.
15
ft-lb (20.4 N-m). If you do not have a torque
wrench, tighten the plug firmly. Do not connect
the wire to the plug.
24
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags,
Model Number38605
Model Year2009
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOperator's Manual
LanguageEnglish
Serial Number290000001 - 290999999
Product NameToro 522 Power Throw Snowthrower
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Product SeriesSnowthrower, Two Stage Small Frame
Swath22 inch
DischargeTwo Stage
Engine ManufacturerTecumseh
Engine Oil Type21 oz. (.62l) 5w-30 or 10w / API SH or higher
Gearbox LubricantAuger 5 oz. Lubriplate Mag 1 grease
Engine Motor Model #LH195SA-67435V
Engine Motor Size195cc
Engine Motor Type4 Cycle, 4 Cycle CARB3, EPA2
Transmission Speed3 Forward/1 Reverse
Transmission TypeFriction Disc
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 522 Power Throw 38605 Snow Blower Operators Manual, 2009 4.0 out of 4.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 522 Power Throw 38605 Snow Blower Operators Manual, 2009 SKU UPC Model
Charles per on Jan 09, 2015. so far so good one I get it started

Having trouble getting it started but once it gets going is awesome


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website