Replacing the Auger/Impeller
Drive Belt
18.
19.
Check the auger/impeller drive linkage and adjust it
if necessary. Refer to steps 4 through 7 of Installing
the Auger/Impeller Drive Control Linkage in Setup.
If the auger/impeller drive belt becomes worn,
oil-soaked, or otherwise damaged, replace the belt.
Install the belt cover.
1.
Remove the 2 flange-head bolts that hold the belt
cover in place and set the cover aside (Figure 36).
Adjusting the Auger/Impeller
Drive Belt
2.
Loosen the belt guide (Figure 37).
Service Interval: After the first hour
3. Remove the auger/impeller drive belt from the
engine pulley and the large auger/impeller pulley
(Figure 37).
Before each use or daily
Operating the snowthrower with an auger/impeller drive
belt that slips decreases the snowthrowing performance
and damages the belt. Check the auger/impeller drive
belt for the proper tension after the first operating hour,
then check and adjust the belt when necessary.
4.
Install a new belt around the large auger/impeller
pulley (Figure 37).
5.
Loop the belt over the engine pulley, ensuring that
the belt is on the inside of the idler pulley and the
belt guide (Figure 37).
6.
Adjust the belt guide so that there is 1/8 inch (3 mm)
of clearance between the auger/impeller drive belt
and the guide, and secure the belt guide.
Improperly adjusting the auger/impeller may
cause it to turn when disengaged. A rotating
auger or impeller can cut off or injure fingers,
hands, or feet.
7. Check and adjust the auger/impeller drive belt as
instructed in Installing the Auger/Impeller Drive
Control Linkage in Setup.
•
Keep your face, hands, feet, and any other
part of your body or clothing away from
concealed, moving, or rotating parts.
8. Install the belt cover.
Important: Do not operate the snowthrower
if the auger and the impeller rotate when you
disengage the auger/impeller drive control lever.
•
•
Ensure that the impeller brake arm clearance
is maintained.
Emptying the Fuel Tank
Do not adjust the auger/impeller drive
belt too tight because it may cause the
auger/impeller to turn when the control
lever is in the Disengaged position. If this
occurs, decrease the belt tension.
1.
Close the fuel shutoff valve (Figure 13).
Gasoline is highly flammable; it can ignite and
cause serious personal injury.
1.
Check and adjust the belt as instructed in Installing
the Auger/Impeller Drive Control Linkage in Setup.
•
•
•
Drain gasoline outdoors
2.
3.
4.
Connect the wire to the spark plug.
Drain gasoline from a cold engine only.
Wipe up any gasoline that may have spilled.
Check the belt tension by operating the auger.
If the belt still slips, replace it. Refer to Replacing the
Auger/Impeller Drive Belt.
• Do not drain gasoline near any open flame
or where gasoline fumes may be ignited by
a spark.
Important: Do not operate the snowthrower
if the auger and the impeller rotate when you
disengage the auger/impeller drive control lever.
•
Do not smoke a cigar, a cigarette, or a pipe
when handling gasoline.
2.
3.
Place a clean drain pan under the fuel shutoff valve.
Loosen the hose clamp that secures the fuel line to
the valve and slide the fuel line off the fuel shutoff
valve (Figure 13).
23
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38605, Toro Power Throw 522 |
| Model Number | 38605 |
| Model Year | 2009 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 290000001 - 290999999 |
| Product Name | Toro 522 Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | Auger 5 oz. Lubriplate Mag 1 grease |
| Engine Motor Model # | LH195SA-67435V |
| Engine Motor Size | 195cc |
| Engine Motor Type | 4 Cycle, 4 Cycle CARB3, EPA2 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 522 Power Throw 38605 Snow Blower Operators Manual, 2009 4.0 out of 4.0 based on 1 product reviews. Having trouble getting it started but once it gets going is awesome