The internal wiring could be damaged during assembly,
causing serious personal injury when operating the
snowthrower.
•
Carefully assemble the snowthrower so that you will not
damage the electrical wiring.
•
If the wiring is damaged, do not assemble the
snowthrower. Contact an Authorized Service Dealer.
Figure 4
3.
Carefully insert the right side of the upper tubing over the end of
the lower right side tubing (Figure 2).
1.
Chute crank
2.
Chute crank gear
10.
Secure the upper and lower tubing and the mounting plate together
with 2 machine screws and 2 locknuts.
Note: Position the screw heads on the outside of the mounting
plate. Be careful not to damage the internal electrical wiring when
you insert the screws. If the wiring blocks the hole, use a blunt
1/8
inch punch to carefully route the electrical wiring away from
the aligned holes.
Installing the Discharge Chute
1.
Position the chute deflector onto the discharge chute and align
the mounting holes (Figure 5).
Figure 2
1.
Upper tubing
2. Lower tubing
4.
Carefully insert the left side of the upper tubing into the end of the
lower left side tubing (Figure 2).
5.
6.
Squeeze the upper tubes together, and wiggle the upper tubes
down until the mounting holes in the upper and lower tubing line
up (Figure 2).
Place the mounting plate over the tubes (Figure 3).
Figure 5
1.
Chute deflector
Discharge chute
Rubber washer (2)
4.
5.
6.
Carriage bolt (2)
Metal washer (2)
Locknut (2)
2.
3.
Figure 3
2.
Insert a rubber washer between the chute deflector and the
discharge chute on each side while maintaining the hole alignment
(Figure 5).
1.
Mounting plate
Shroud
3.
4.
Chute crank
Gear
2.
3.
Secure the deflector to the discharge chute with 2 carriage bolts, 2
metal washers, and 2 locknuts.
7.
Align the mounting plate holes with the upper and lower tubing
holes.
Note: Ensure that the square shoulders on the carriage bolts align
with the inside square on the discharge chute. Position the metal
washers to the outside of the chute deflector as shown in Figure 5.
Do not overtighten the bolts.
8.
9.
Insert the end of the chute crank through the hole in the shroud.
Turn the chute crank rod slowly until the flattened end drops into
the slot in the gear, then firmly push the chute crank into the gear
until it snaps into place (Figure 3 and Figure 4).
3
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 1800 Power Curve, Toro 38025 |
| Model Number | 38025 |
| Model Year | 2010, 2011 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 310000001 - 310999999, 311000001 - 311999999 |
| Product Name | 1800 Power Curve Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower |
| Swath | 18 inch |
| Discharge | Single Stage |
| Engine Motor Size | 12 amp |
| Engine Motor Type | 120-VAC |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)