STARTING AND STOPPING
See Figures 9 - 10.
HALF
CHOKE
FULL
CHOKE
To start a cold engine:
DO NOT squeeze the throttle trigger until the engine starts
FULL
HALF
FULL
HALF
and runs.
RUN
RUN
1.
2.
Set the Powervac on a flat, bare surface.
™
Slowly press the primer bulb 8 times.
NOTE: After the 8th press, fuel should be visible in
the primer bulb. If it is not, continue to press the primer
until you see fuel in the bulb.
3.
4.
5.
Place the choke lever in the FULL CHOKE position.
RUN
POSITION
Pull throttle lock back to lock the throttle wide open.
Pull the starter grip and rope sharply until engine at-
tempts to run. Do not pull the starter grip more than
four (4) times.
FULL
HALF
6.
7.
Set the choke lever in the HALF CHOKE position.
RUN
Pull the starter grip and rope until the engine runs. Do
not pull the starter grip more than six (6) times.
NOTE: If the engine does not start, return to the FULL
CHOKE position and repeat steps 3 through 6 again.
8.
Allow the engine to run for 20 seconds, then place the
choke lever in the RUN position.
Figure 10
NOTE: In cooler environments, additional pulls of the
starter handle may be required with the choke lever in
the FULL CHOKE position.
OPERATING THE BLOWER
See Figures 11 - 12.
STOP
SWITCH
WARNING:
Never run the unit without the blower tubes
THROTTLE
TRIGGER
installed or the vacuum door securely closed.
Failure to follow these steps could result in pos-
sible serious injuries.
WARNING:
CHOKE
LEVER
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with
hearing protection. Failure to do so could result
in objects being thrown into your eyes and other
possible serious injuries.
STARTER
GRIP AND
ROPE
1.
Start the blower. Refer to Starting and Stopping earlier
in this manual. Hold the blower with the upper handle
in your right hand.
PRIMER BULB
Figure 9
To start warm engine:
WARNING:
1
.
Place the choke lever in the RUN position.
Keep away from the muffler and all other hot
surfaces of the blower. Failure to do so could
result in possible serious personal injury.
2.
3.
Pull throttle lock back to lock the throttle wide open.
Pull the starter grip and rope until the engine runs.
NOTE: If the engine does not start, repeat steps 3
through 7 again.
2.
To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the
center of a pile.
To stop the engine:
1.
Press and hold the stop switch in the stop (O) position
until the engine stops.
Operation
15
Categories | Blower Vacuum and Sweeper Manuals, Toro Blower and Vacuum Manuals |
---|---|
Tags | Toro 51984 |
Model Number | 51984 |
Model Year | 2010 |
Download File |
|
Document Type | Operator's Manual |
Language | English, Français, Español |
Serial Number | 310000001 - 310999999 |
Product Name | Powervac Gas-Powered Blower |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Blowers, Vacuums |
Product Type | Blower, Vacuum |
Product Series | Blower, Hand Held Gas Powered |
Engine Manufacturer | OWT/TTI |
Engine Motor Size | 25cc |
Engine Motor Type | 2 Cycle |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)