Checking and Adjusting the
Skids
Note: The pivoting scraper on the machine is not
recommended for use on gravel surfaces. But if you
must use the machine on a gravel surface, adjust the
skids further down to prevent the pivoting scraper
from picking up rocks.
Service Interval: Yearly—Check the skids and adjust
them if necessary (model 38654 only).
6.
Firmly tighten the nuts that secure both skids to the
auger sides.
Model 38654 only
Check the skids to ensure that the auger does not
contact the paved or gravel surface. Adjust the skids as
needed to compensate for wear.
Note: If the skids become excessively worn, you
can turn them over and set the unused side toward
the pavement.
1.
Check the tire pressure. Refer to Checking the Tire
Pressure.
Checking and Adjusting the
Traction Cable
2.
3.
Move the machine to a level surface.
Loosen the nuts that secure both skids to the
auger sides until the skids slide up and down easily
(Figure 45).
Service Interval: After the first 2 hours—Inspect
the traction cable and adjust it if
necessary.
Yearly—Inspect the traction cable
and adjust or replace it if necessary.
If the machine does not drive in the forward or reverse
speeds or it drives when you release the traction lever,
adjust the traction cable.
Figure 45
With the traction lever disengaged, check the pin in the
elongated slot in the left side of the machine above the
tire. There should be a gap of 1/32 to 1/16 inch (1 to
1.5 mm) from the front of the slot to the front edge of
the pin (Figure 47).
1.
Skid
4.
Push down on the handles to allow the pivoting
scraper to move fully forward, then set the front
of the machine down so that the front edge of the
pivoting scraper contacts the ground (Figure 46).
Figure 47
1.
2.
Pin
1/32 to 1/16 inch (1 to 1.5 mm)
Figure 46
1.
Pivoting scraper
If the left hand (traction) cable is not properly adjusted,
do the following steps:
5.
Move the skids down until they are even with the
ground.
1.
2.
Loosen the jam nut.
Loosen or tighten the turnbuckle to adjust the pin
until it is the proper gap from the front edge of the
slot.
Note: For a smooth surface, you can set the skids
slightly higher to increase the scraping action, but
set the skids far enough down to prevent the auger
blades from contacting the ground.
3. Tighten the jam nut (Figure 48).
22
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38614, Toro 38624, Toro 38624W, Toro 38634, Toro 38644, Toro 38654, Toro Power Max 726OE |
| Model Number | 38614, 38624, 38624W, 38634, 38644, 38654 |
| Model Year | 2011 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 311000001 - 311999999 |
| Product Name | Toro Power Max 726 OE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | 20 oz. (.6l) 5w-30 or 10w-30 / API SH or higher |
| Engine Motor Model # | 15C1040139E8 |
| Engine Motor Type | 4 Cycle, 4 Cycle CARB2, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro Power Max 726OE 38614 38624 W 38634 38644 38654 Snow Blower Operators Manual, 2011 5.0 out of 5.0 based on 1 product reviews. I need to clean carburetor left gas in it need to said more.