Important: Refer to your engine operator's manual for additional maintenance procedures. For engine adjustments,
repairs, or warranty service not covered in this manual, contact an Authorized Briggs & Stratton Servicing Dealer.
Checking and Adjusting the
Service Interval: Before each use or daily
Skids and Scraper
Preparing for Maintenance
Service Interval: Yearly—Check the skids and the scraper
1.
2.
3.
Move the machine to a level surface.
and adjust them if necessary.
Stop the engine and wait for all moving parts to stop.
Check the skids and the scraper to ensure that the auger does
not contact the paved or gravel surface. Adjust the skids and
the scraper as needed to compensate for wear.
Disconnect the spark plug wire. Refer to Replacing
the Spark Plug.
1.
Check the tire pressure. Refer to Checking the Tire
Pressure.
Checking the Engine Oil Level
2.
Loosen the nuts that secure both skids to the auger
sides until the skids slide up and down easily.
Service Interval: Before each use or daily—Check the engine
oil level and add oil if necessary.
1.
2.
Remove the dipstick, wipe it clean, then fully install
the dipstick.
Remove the dipstick and check the oil level (Figure 36).
If the oil level is below the Add mark on the dipstick,
add oil. Refer to Filling the Engine with Oil.
1
g019046
Figure 37
1.
1/8 inch (3 mm)
Important: The auger blades must be supported
above the ground by the skids.
g018886
3.
Ensure that the scraper is 1/8 inch (3 mm) above and
parallel to a level surface.
Figure 36
Note: If the pavement is cracked, rough, or uneven,
adjust the skids to raise the scraper. For gravel surfaces,
adjust the skids further down to prevent the machine
from picking up rocks.
4.
5.
Move the skids down until they are even with the
ground.
Firmly tighten the nuts that secure both skids to the
auger sides.
Note: To quickly adjust the skids if they loosen,
support the scraper 1/8 inch (3 mm) off the pavement,
then adjust the skids down to the pavement.
Note: If the skids become excessively worn, you can
turn them over and set the unused side toward the
pavement.
20
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 37777, Toro Power Max 826 OTE |
| Model Number | 37777 |
| Model Year | 2015 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 315000001 - 315999999 |
| Product Name | Power Max 826 OTE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | 18 oz. (.54l) 30w or 10w-30 / API SF or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | 12D1050172F8 |
| Engine Motor Size | 205cc |
| Engine Motor Type | 4 Cycle |
| Engine Speed | 3300±100 RPM |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Tire Pressure | 17-20 PSI / 116-137 kPa |
| Spark Plug | Champion QC12YC |
| Spark Plug Gap | .030"/ .76mm |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)