FRICTION DISC REPLACEMENT
3
1.
Shut off engine, remove key, disconnect
spark plug wire and allow unit to cool
completely.
1
5
2.
Place unit into service position on a level
surface.
7
3.
4.
Remove both wheels.
Remove bottom cover by removing six
hex bolts.
2
5.
6.
Disconnect pivot pin from the speed
selector arm. Save the hardware for
reinstallation.
Remove spring clip pin nearest drive
sprocket from hex shaft.
7.
8.
Remove left bearing flange from frame.
Slide hex shaft to the left to remove
pinion sprocket and friction disc
assembly from hex shaft.
4
NOTE: Be sure to save washers between
bearing and sliding fork for re-assembly.
OS7142
6
1.
2.
Hex Shaft
Bearing
Flange
Speed
Selector
Arm
4. Friction Disc
5. Spring Clip
6. Drive Plate
Assembly
7. Drive
Sprocket
9.
10.
11.
Remove friction disc assembly from
frame.
Remove three screws holding friction
disc to carrier bearing.
Remove old friction disc. Put the new
friction disc in place, cup side to carrier
bearing.
3.
Figure 48
12.
13.
Reinstall three screws onto new friction
disc and carrier bearing. Torque to
5 – 6 lbf-ft (22.2 – 26.7 N•m).
Insert new friction disc assembly into
frame. Install washers onto carrier
bearing and slide into speed selector
arm.
Slide hex shaft through new friction disc
assembly. Install pinion sprocket onto
hex shaft and slide shaft into right
bearing.
Install left bearing using hardware
removed in step 7.
TRACK TENSION ADJUSTMENT
(921014, 015, 016)
Check the track tension by applying pressure
on the track midway between the upper and
rear track rollers. Deflection should be
approximately 3/8 in. (9.6 mm). See
Figure 49.
14.
15.
If deflection is excessive, tighten the track
tension.
16.
17.
Reinstall clip pin into hex shaft.
Connect pivot pin to speed selector arm
(see Discharge Chute on page 29).
3/8 in.
(9.6 mm)
18.
19.
20.
21.
22.
Replace bottom cover.
Install wheels.
Return unit to upright position.
Connect spark plug wire to spark plug.
Adjust traction drive clutch (see Traction
Drive Clutch Adjustment on page 32).
Figure 49
OS7226
If unit pulls to the left or right when a straight
path is desired adjust the track tension. If the
unit is pulling to the left, tighten the left track
adjuster. If the unit is pulling to the right,
tighten the right track adjuster.
To adjust (Figure 50):
1.
Tighten the adjuster nut to tighten the
track tension.
GB - 34
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 921011, Ariens 921012, Ariens 921013, Ariens 921014, Ariens 921015, Ariens 921016, Ariens 921017, Ariens 921018, Ariens 921019, Ariens 921020, Ariens 932105, Ariens 932506, Ariens Deluxe 24, Ariens Deluxe 24 Platinum, Ariens Deluxe 27, Ariens Deluxe 30, Ariens Deluxe 30 Platinum, Ariens Deluxe Track 24, Ariens Deluxe Track 27, Ariens Deluxe Track 30, Ariens Snow Blower Manuals |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)