FILLING FUEL TANK
2. Check Function of Clutches
If clutches do not engage or disengage properly, adjust
or repair before operation (see SERVICE AND
ADJUSTMENTS on page 18).
WARNING: AVOID INJURY. Read and
understand the entire Safety section before
proceeding.
3. Check Adjust Axle Lock
Fuel Shut-Off Valve
Use the axle lock pins to lock or unlock the wheels.
Lock both wheels to increase traction; unlock one
wheel to allow for easier turning of the unit.
IMPORTANT: The fuel shut-off valve MUST be in the
closed position prior to transporting the unit.
The fuel shut-off valve has two positions:
4. Check Runners
•
Closed Position: Use this position to service,
transport, or store the unit.
Check and adjust Runners (SERVICE AND
ADJUSTMENTS on page 18). Allow 1/8 in. (3 mm)
between scraper blade and hard, smooth surface(s).
Allow 1-1/4 in. (30 mm) between scraper blade and
uneven or gravel surfaces.
•
Open Position: Use this position to run the unit.
CLOSED
OPEN
5. Check Engine Fuel & Crankcase Oil
WARNING: AVOID INJURY. Read and
understand the entire Safety section before
proceeding.
Figure 10
Check and add fuel if required. Check that the engine
crankcase oil is full using dipstick. Refer to Engine
Manual for detailed instructions.
To add fuel to fuel tank:
1.
ALWAYS place unit in open or well-ventilated
area.
TO STOP IN AN EMERGENCY
2.
3.
Stop engine and allow to cool.
Immediately release both control levers to stop unit in
an emergency. Stop engine, remove key and wait for
all rotating parts to stop before leaving operator’s
position.
Clean Fuel Cap and surrounding area to prevent
dirt from entering Fuel Tank.
4.
Remove Cap.
IMPORTANT: DO NOT use gasohol or gasoline
containing alcohol. See Engine Manual for correct type
and grade of fuel.
STARTING AND SHUT OFF
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in personal
injury and/or damage to unit. DO NOT
attempt to start your unit at this time. Read
entire Owner/Operator Manual and the
Engine Manual first.
5.
Fill fuel tank to within 1/2 in. (1.2 cm) below
bottom of filler neck with unleaded gasoline.
NOTE: Tank capacity is 3.5 qt (3.3 L) (932041, 042,
141, 509, 510, 511) or 2 qt (1.96 L) (932040, 140).
6.
7.
Replace Fuel Cap and tighten.
IMPORTANT: Allow unit and engine to adjust to the
outdoor temperature before clearing snow. Before
shut-off, run the attachment a few minutes to prevent
impeller freeze-up.
ALWAYS clean up any spilled fuel.
PRE-START
1. Frozen Impeller
NOTE: Try out each control without the engine running
to see how it works and what it does.
IMPORTANT: Before starting engine, check impeller to
be sure it is not frozen.
Manual Start
To check impeller:
1.
Turn discharge chute straight ahead.
1.
With ignition key switch in “Stop” position,
squeeze Attachment Clutch Lever to Engaged
position.
2. Make sure that the traction clutch and attachment
drive clutch levers are fully disengaged.
2.
3.
Pull Recoil Starter Handle.
3. Push Primer Bulb 2 or 3 times for cold engine.
If Impeller is frozen, (cannot pull Starter Handle)
move unit to a heated area and thaw to prevent
possible damage.
NOTE: When temperature is below -15° F (-26° C)
additional priming may be needed.
4.
If engine is cold, apply choke. See Engine
Manual for detailed instructions.
NOTE: A warm engine requires less choking than a
cold engine.
GB - 14
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 932040, Ariens 932041, Ariens 932042, Ariens 932140, Ariens 932141, Ariens 932509, Ariens 932510, Ariens 932511, Ariens ST5520, Ariens ST5520E, Ariens ST624, Ariens ST624E, Ariens ST7524, Ariens ST7524E |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)