12.
13.
Slide friction disc assembly and hex shaft to the
right until the left end of shaft is clear of left
bearing. Tap lightly if necessary, to loosen. The
shaft slides out of the small pinion gear and
washer.
3
4
5
2
1
Carefully lift shaft and friction disc out of unit. As
you remove the assembly, the washers between
the bearing and sliding forks will be loose. Do not
lose the washers.
4
6
11
2
3
5
1
6
11
5
1
0
6
9
8
7
1.
2.
3.
Traction Clutch Cable
Shift Rod
Attachment Control
Cable
Mounting Nuts
Attachment Clutch
Arm
6.Speed Selector Arm
7.Adjustment Pivot Pin
8.Cotter Pin and Clevis
9.Jam Nut
10.Traction Drive Clutch
Arm
4.
5.
11.Adjustment Barrel
Figure 26
OS6780
8
9
7
FRICTION DISC REPLACEMENT
10
6
1.
2.Friction Disc
3.Hex Bolts & Nuts
4.
5.
6.
Hex Shaft
7.Bearing Cap Screws
8.Bearing Cap/Bushing
9.Clutch Fork
10.Large Gear
11.Pinion Gear
Remove Friction Disc
(Figure 27):
Shift Carrier
Roll Pins
Washers
1.
Shut off engine, remove key, disconnect spark
plug wire and allow unit to cool completely.
Figure 27
OS2002
CAUTION: Before tipping unit, remove
enough fuel so that no spills occur.
Replace Friction Disc
1.
2.
3.
Remove three hex bolts and nuts holding friction
disc to shift carrier.
2.
3.
Tip the unit up onto front housing on a level
surface.
Remove the old friction disc. Put the new friction
disc in place, flat side to the shift carrier.
Remove lockpins from wheel axles and remove
wheels.
Reinstall the three bolts and nuts into the new
friction disc and hub. Torque to 5-6 lbf-ft (6.8 to
8.13 N•m).
4.
5.
6.
Remove two bolts from top of bottom cover.
Loosen two bottom screws and slide cover off.
Disconnect pivot pin from the speed selector arm.
Save the hardware for reinstallation.
Reinstall Friction Disc
1.
2.
3.
Reinstall the shift carrier, the small pinion gear
and washer onto the hex shaft. The washer goes
between the bearing and the pinion gear.
7.
8.
Carefully tap two roll pins out of center and right
end of shaft.
Remove four nuts from bearing cap on left side of
unit. Remove bearing and outside bearing cap.
Slide the shaft and attached parts into the frame,
through the right side hole first, then the left.
Pinion gear must mesh with the large gear.
9.
Reinstall one nut to keep the inside bearing cap
in place.
Reinstall the flange bearing and washers into the
shift forks. Be sure the washers are inside the
forks.
10.
11.
Remove bearing cap/bushing and washer from
right side of unit.
Reinstall nuts on screws through side frame to
keep screws in place.
4.
5.
Reinstall the bearing and outside bearing cap on
the left side of the frame.
On the right side of the frame, place the washer
on the end of the shaft.
GB - 23
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 932040, Ariens 932041, Ariens 932042, Ariens 932140, Ariens 932141, Ariens 932509, Ariens 932510, Ariens 932511, Ariens ST5520, Ariens ST5520E, Ariens ST624, Ariens ST624E, Ariens ST7524, Ariens ST7524E |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)