OPERATION
o n / of f SWiTCH
DRIVE
CONTROL
Press into the ON position when starting the engine and will shut off
the engine when moved into the OFF position.
r eCo iL STar Ter HanDLe
This handle is used to manually start the engine.
eLeCTr iC STar Ter bUTTo n
Pressing the electric starter button engages the engine’s electric
starter when plugged into a 120V power source.
GO
NOTE: Always release the wheel drive control before changing
speeds. Failure to do so will result in increased wear on your machine’s
drive system.
eLeCTr iC STar Ter oUTLeT
Requires the use of a three-prong outdoor extension cord (included)
and a 120V power source/wall outlet.
TWo -WaY CHUTe Co nTr oL™
aUger S
The distance snow is thrown can be changed by adjusting the angle
of the chute assembly. Move the chute control forward to decrease the
distance, toward the rear to increase.
When engaged, the augers rotate and draw snow into the auger
housing.
CHUTe aSSeMbLY
CHUTe Dir eCTio naL Co nTr oL
The chute directional control is located on the left side of the snow
thrower.
Snow drawn into the auger housing is discharged out the chute
assembly.
•
To change the direction in which snow is thrown, crank clockwise to
gaS CaP
discharge to the left and counterclockwise to discharge to the right.
Unthread the gas cap to add gasoline to the fuel tank.
SkiD SHo eS
Position the skid shoes based on surface conditions. Adjust upward
for hard-packed snow. Adjust downward when operating on gravel or
crushed rock surfaces.
aUger Co nTr oL
AUGER
CONTROL
WHeeL STeer ing Co nTr oLS
The left and right wheel steering controls are located on the underside
of the handles. Squeeze the right control to turn right; squeeze the left
control to turn left.
NOTE: Operate the snow thrower in open areas until you are familiar
with these controls.
GO
HeaDLigHT
The auger control is located on the left handle. Squeeze the control
grip against the handle to engage the augers and start snow throwing
action. Release to stop.
The headlight is located on top of the handle panel. It may be adjusted
by loosening the screws on each side of the light housing, pivoting the
light up or down, and retightening the screws.
WHeeL Dr iVe Co nTr oL /aUger Co nTr oL Dr if T CUTTer S
Lo Ck
Theoptionaldriftforcuttersnormalaresnowdesignedconditions.for use in deep snow. Their use is
The wheel drive control is located on the right handle. Squeeze the
control grip against the handle to engage the wheel drive. Release
to stop. The Wheel drive control also locks the auger control so you
can operate the chute directional control without interrupting the snow
throwing process. If the auger control is engaged simultaneously with
the wheel drive control, the operator can release the auger control (on
the left handle) and the augers will remain engaged. Release both
controls to stop the augers and wheel drive.
CLean-o UT To oL
The chute clean-out tool is conveniently fastened to the rear of the
auger housing with a mounting clip. Should snow and ice become
lodged in the chute assembly during operation, proceed as follows to
safely clean the chute assembly and chute opening.
13
| Categories | Craftsman Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Craftsman 24788845 |
| Model Number | 247.88845 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Español |
| Product Name | Craftsman 45-Inch |
| Product Brand | Craftsman. Customer Service Representatives are available by phone: Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Swath | 45 inch |
| Engine Oil Type | SAE 5W30, 4-Cycle Engine Oil (Quart) Recommended for Temperature: - Above 32°F: SAE 30W Straight Grade; - 0°F to 32°F: SAE 5W-30 or SAE 10W-30 Multi Grade; - Below O°F: SAE 0W-30 Synthetic |
| Document File Type | |
| Publisher | craftsman.com |
| Wikipedia's Page | Craftsman (tools) |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)