Craftsman 675 247.77640 Log Splitter Lawn Mower Owners Manual

OPERATION
USinG t he  LOG SPLit t eR
1.
2.
Place the log splitter on level, dry ground.
Place the beam in either the horizontal or vertical position  and lock
in place with the appropriate locking rod.
Block the front and back of both wheels.
Placedirectiontheoflogtheagainstgrain. the end plate and only split wood in the
To stabilize the log, place your hand only on sides of log. Never
place hand on the end between  the log and the splitting
wedge.
Only one adult should stabilize the log and operate the  control
handle, so the operator has full control over the log and the splitting
wedge.
3.
4.
5.
6.
Control handle
1.
2.
3.
Move control handle FORWARD or DOWN to split wood.
Release the control handle to stop the wedge movement.
Move control handle BACK or UP to return the wedge.
Log dislodger
The log dislodger is designed to remove any partially  split wood from
the wedge. This may occur while splitting  large diameter wood or
freshly cut wood.
Figure -
WaRninG
Never remove partially split wood from the wedge with  your hands.
St aRt inG  enGine
Attach spark plug wire to spark plug. Make certain  the metal cap on
Fingers may become trapped between split  wood.
1.  To remove partially  split wood from wedge, move control handle to
REVERSE position until wedge is fully retracted to allow split  wood
portion to contact the log dislodger.
2.
3.
4.
Push stop switch to ON.
2.
Once removed from wedge with log dislodger, split wood from
Move choke control to CHOKE position.
opposite end or in another location.
Grasp starter handle and pull rope out slowly  until engine reaches
start of compression cycle (rope  will pull slightly harder at this
point).
vertical Position
1.
2.
3.
Pullbeamthetohorizontalthe verticalbeamposition.lock out to release the beam and pivot the
5.
6.
Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip
on starter handle. Let rope rewind slowly.
To lock the beam in the vertical position,  pull out on the vertical
beam lock and rotate it to secure the beam. See Figure 4-1.
Stand in front of the unit to operate the control handle and  to
stabilize the log. See Figure 4-3.
Repeat, if necessary, until engine starts. Slowly  adjust choke
toward RUN position. Wait until engine runs smoothly before each
choke adjustment.
7.
If engine falters, move control lever to CHOKE position, then  slowly
horizontal Position
back to RUN position.
1.
Pull the vertical beam lock out and rotate it down. See Figure  4-1.
Pivot beam to the horizontal position. The beam will lock automati-
cally in horizontal position.
8.
If weather is cold, run wedge up or down beam 6 to 8 times to
circulate the hydraulic fluid.
2.
Stand behind the reservoir tank to operate control  handle and to
WaRninG
stabilize the log.
When starting a warm engine, the muffler and surrounding  areas are
hot and can cause a burn. Do not touch.
10
Product Specification
CategoriesCraftsman Lawn Mower Manuals, Lawn Mower Manual
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 48 pages
Document TypeOperator's Manual
LanguageEnglish
Product BrandCraftsman. Customer Service Representatives are available by phone: Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishercraftsman.com
Wikipedia's PageCraftsman (tools)
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website