Craftsman 675 247.77640 Log Splitter Lawn Mower Owners Manual

ASSEMBLY
2.
3.
4.
5.
Disconnectthe six hex screws.the dislodgerSee Figurefrom the3-4.beam weld bracket by removing
Disconnect the log cradle from the beam  on the side of the control
valve. See Figure 3-5.
Liftbrackets.and slide the cylinder up to the top of beam and into the weld
Attachhardware,the previouslydislodger overremoved,the wedgeto theassemblyweld brackets.and secure with
NOTE: Once the six hex screws are tightened, there  may be a slight
gap between the dislodger and the weld brackets.  This gap is normal.
6.
Reattach the log cradle to the side of the beam  with the control
valve, aligning the ends of the cradle with the beam flanges.
7.
Roll log splitter off the bottom crate.
Figure -
PRePaRinG  t he  LOG SPLit t eR
1.
Lubricate the beam area (where the splitting  wedge will slide) with
engine oil; do not use grease.
2.
Removeengine onventedtop ofreservoirthe reservoirdipstick,tank.whichSee Figureis located3-6.in  front of the
IMPORTANT: The log splitter may have been shipped and primed
with hydraulic fluid in the reservoir tank.  However, you MUST check
the fluid level before operating. If not filled, proceed with  the following
steps:
3.
Fill the reservoir tank with hydraulic fluid included  with this unit (if
equipped) or approved fluids which include  Dexron® III / Mercon®
III automatic transmission fluid, a 10 Weight AW hydraulic oil or
Pro-Mix™ AW-32 Hydraulic Oil.
4.
5.
Check fluid level using the dipstick. See Figure  3-6. Do not overfill.
Replace vented dipstick securely, tightening it until the  top of the
threads are flush with top of the pipe.
Figure -
6.
7.
Disconnectstarter as fartheassparkit will pluggo. Repeatand primeapproximatelythe pump by10pullingtimes. the recoil
Reconnect the spark plug wire and start  engine following instruc-
tions in the OPERATION section.
8.
9.
Useposition.controlThenhandleretractto theengagewedge.the wedge to the farthest extended
Refill tank as specified on the dipstick.
NOTE: Failure to refill the tank will void unit’s warranty.
10.
Extend and retract the wedge 12 complete cycles  to remove
trapped air in the system (the system is “self-bleeding”).
11.
Refill reservoir within range marked on the dipstick.
WaRninG
Much of the original fluid has been drawn into the cylinder  and hoses.
Make certain to refill the reservoir to prevent damage to the  hydraulic
pump.
Figure -
NOTE: Some fluid may overflow from the vent plug as the  system
builds heat and the fluid expands and seeks a balanced level.

Product Specification
CategoriesCraftsman Lawn Mower Manuals, Lawn Mower Manual
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 48 pages
Document TypeOperator's Manual
LanguageEnglish
Product BrandCraftsman. Customer Service Representatives are available by phone: Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishercraftsman.com
Wikipedia's PageCraftsman (tools)
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website