3
- ASSEMBLY INSTRUCTIONS
3 - ASSEMBLY INSTRUCTIONS
CAUTION
1
0. Turn the knob (J) COUNTERCLOCKWISE until the
TANG (K) is to the end of its travel. (Fig. 3-3F)
Install the clutch cover making sure the tang is posi-
tioned in the lower hole in the guide bar. Make sure
the chain does not slip off of the bar.
Lock the screw (N) be tight, and follow step 13 to
adjust the chain tension.
Turn the tension ring clockwise tight (M); pull the con-
trol button by arrow direction (L) to turn tightly be
clockwise then push the control button back. (Fig. 3-
3G)
3-4. SAW CHAIN TENSION ADJUSTMENT
Proper tension of saw chain is extremely important and
must be checked before starting, as well as during any cut-
ting operation.
TO TEST CHAIN BRAKE :
®
1.
The CHAIN BRAKE is DISENGAGED (chain can
®
A new saw chain stretches, requiring adjustment after as
few as 5 cuts. This is normal with a new chain, and the
interval between future adjustments will lengthen quickly.
11.
move) when BRAKE LEVER IS PULLED BACK AND
LOCKED. Be sure the chain break latch is in the on
position. (Figure 3-5A).
Taking the time to make needed adjustments to the saw
chain will result in improved cutting performance and pro-
longed chain life.
CAUTION
12.
13.
2.
The CHAIN BRAKE is ENGAGED (chain is stopped)
®
If saw chain is TOO LOOSE or TOO TIGHT, the sprocket,
bar, chain, and crankshaft bearings will wear more rapidly.
Study Figure 3-4B for information concerning correct cold
tension (A), correct warm tension (B), and as a guide for
when saw chain needs adjustment (C).
when brake lever is in forward position and the chain
brake latch is in the off position. You should not be
able to move chain (Figure 3-5B).
NOTE: The brake lever should snap into both positions. If
strong resistance is felt, or lever does not move into either
position, do not use your saw. Take it immediately to an
Authorized Service Center for repair.
WARNING
Always wear heavy duty gloves when handling saw chain
or making saw chain adjustments.
TO ADJUST SAW CHAIN:
NOTE: The guide bar retaining knob is installed only hand
tight at this point because saw chain adjustment is
required. Follow instructions in Section, Saw Chain Tension
Adjustment.
1
.
Hold nose of guide bar up and turn adjustment chain
ring (A) CLOCKWISE to increase chain tension.
Turning chain ring (A) COUNTERCLOCKWISE will
decrease amount of tension on chain. Ensure the
chain fits snugly all the way around the guide bar. (Fig.
3-4A)
2.
After making adjustment, and while still holding nose
of bar in the uppermost position, tighten the bar
retaining button (B) securely. Chain has proper ten-
sion when it has a snug fit all around and can be
pulled around by gloved hand. (Fig. 3-BA)
A
B
J
C
ON
3-4B
NOTE: If chain is difficult to rotate on guide bar or if it binds,
too much tension has been applied. This requires minor
adjustment as follows:
A. Loosen the bar retaining knob so it is finger tight.
Decrease tension by turning the bar adjustment chain
ring COUNTERCLOCKWISE slowly. Move chain back
and forth on bar. Continue to adjust until chain rotates
freely, but fits snugly. Increase tension by turning bar
adjustment chain ring CLOCKWISE.
3-5.
®
Your chain saw is equipped with a CHAIN BRAKE that
CHAIN BRAKE®MECHANICAL TEST
3-5A
reduces possibility of injury due to kickback. The brake is
activated if pressure is applied against brake lever when,
as in the event of kickback, operator’s hand strikes the
lever. When the brake is actuated, chain movement stops
abruptly.
K
WARNING
B.
When saw chain has proper tension, hold nose of bar
in uppermost position and tighten the bar retaining nut
securely.
The purpose of the CHAIN BRAKE is to reduce the possi-
®
bility of injury due to kickback; however, it cannot provide
the intended measure of protection if the saw is operated
carelessly.
OFF
Always test the CHAIN BRAKE before using your saw and
®
periodically while on the job.
3-3F
A
3-5B
L
B
3-4A
M
N
3-3G
8
9
| Categories | Chainsaw Manuals, Eager Beaver Chainsaw Manuals, McCulloch Chainsaw Manuals |
|---|---|
| Tags | Eager Beaver EBC1840DK, Mcculloch Chain Saws, McCulloch EBC1840DK |
| Download File |
|
| Language | English |
| Product Brand | McCulloch. Support Phone for US: Wheeled (Mowers, Tractors, Tillers, Snow Throwers) - 1-800-849-1297
McCulloch Handheld (Chainsaws, Trimmers, Blowers, Edgers) - 1-800-554-6723 All McCulloch Products - 1-800-521-8559, Chainsaw |
| Document File Type | |
| Publisher | mcculloch.com |
| Wikipedia's Page | McCulloch Motors |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)