MTD 230 240 250 260 261 S230 S240 S250 S260 S261 Snow Blower Owners Manual

5
7.
As engine warms up and begins to operate evenly,
rotate choke lever slowly to the 1/2 Choke position.
When the engine begins to run smoothly, move the
choke to the OFF position. If engine falters, return
to FULL choke, then slowly move to 1/2 then OFF
position.
Operating the Snow Thrower
The pitch of the chute assembly controls the angle  at
which the snow is thrown.
1.
Loosen the star knob found on the left side of the
chute assembly and
pivot the upper chute
To Stop Engine
1.
Operation
upward or downward
to the desired pitch.
To stop engine, turn ignition key counter-clockwise.
Disconnect the spark plug wire from the spark  plug
to prevent accidental starting while equipment  is
unattended.
Retighten the star
knob before operating
the snow thrower.
2.
Position the chute
To help prevent possible freeze-up  of starter,
assembly opening
proceed as follows:
Figure 6
by using the Chute
1.
2.
Run engine for a few minutes before stopping to help
dry off any moisture on the engine.
Handle to throw the snow in the desired direction.
See inset Figure 6.
WARNING
Electric Starter: Connect power cord  to switch box
on engine, then to 120 volt AC receptacle. With the
engine running, push starter button and  spin the
starter for several seconds. The unusual sound made
by spinning the starter will not harm engine or starter.
Disconnect the power cord from receptacle  first, and
then from switch box.
Clearing Snow
Muffler, engine and
surrounding areas
become hot and
can cause a burn.
Do not touch.
WARNING: Never operate  the snow
thrower with bystanders in front of or
near the discharge chute opening.
Engage the auger by squeezing the auger control
handle against the upper handle. See Figure 5.
1.
2.
3.
Recoil Starter: With engine running,  pull starter rope
with a rapid, continuous full arm stroke three or four
times. Pulling the starter rope will produce  a loud
clattering sound, which is not harmful to the engine  or
starter.
Lift up slightly on the handle to allow the rubber
paddles on the auger to contact the pavement and
propel the snow thrower forward. Pushing downward
on the handle will raise the augers off the ground
and stop forward motion.
Never operate the
snow thrower with
bystanders in front of
or near the discharge
chute opening.
4.
5.
Wipe all snow and moisture from the carburetor cover
in the area of the control levers. Also, move control
levers back and forth several times. Leave choke
control in the FULL choke position.
3.
Discharge snow downwind whenever possible.
Slightly overlap each previously cleared path.
NOTE: Excessive upward pressure on the handle will
result in premature wear on the rubber auger blades
which would not be covered by warranty.
Remove ignition key and disconnect spark plug  wire to
prevent accidental starting.
Operating Tips
1.
Run the engine for a few minutes before stopping to
help dry any moisture on the engine.
NOTE: Excessive
upward pressure on
the handle will result
in premature wear
on the rubber auger
blades which would
not be covered by
warranty.
2.
Clean the snow thrower thoroughly after each use.
WARNING: Muffler, engine and
surrounding areas become hot and
can cause a burn. Be careful and do
not touch when hot.

Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags, , , , , , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 18 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website