2
Safe
Operation
Practices
Operation
Maintenance & Storage
1.
2.
3.
Do not put hands or feet near rotating parts, in the auger/
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjust-
ment sections of this manual.
2. Before cleaning, repairing, or inspecting machine disengage
all control levers and stop the engine. Wait until the auger/
impeller come to a complete stop. Disconnect the spark plug
wire and ground against the engine to prevent unintended
starting.
The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
4.
5.
Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
6.
7.
Do not operate machine while under the influence of alcohol 5. Snow thrower shave plates and skid shoes are subject to
or drugs.
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
Maintain or replace safety and instruction labels, as neces-
sary.
Muffler and engine become hot and can cause a burn. Do
not touch.
8.
9.
Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
Exercise caution when changing direction and while operat-
ing on slopes.
6.
WARNING
10.
Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
7.
This symbol points
out important safety
instructions, which
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
8.
Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
11.
12.
13.
9.
Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
10.
Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
11.
12.
Always refer to the operator’s manual for proper instructions
on off-season storage.
14.
15.
Disengage power to the auger/impeller when transporting or
not in use.
Check fuel line, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
Never operate machine at high transport speeds on slippery
surfaces. Look down and behind and use care when
backing up.
13. Do not crank engine with spark plug removed.
16.
17.
If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way.Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
result in personal
Notice regarding Emissions
injury. When you see
this symbol, HEED
IT’S WARNING!
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modifica-
tion (EM) Oxidizing Catalyst (OC), Secondary Air Injection (SAI)
and Three Way Catalyst (TWC) if so equipped.
18.
Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the dis-
charge opening. Do not unclog chute assembly while engine
is running. Shut off engine and remain behind handles until
all moving parts have stopped before unclogging.
Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
Average Useful Life
19.
20.
According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
When starting engine, pull cord slowly until resistance is felt, this product has an
of seven (7) years, or
Average Useful Life
and follow the warnings
and instructions
then pull rapidly. Rapid retraction of starter cord (kickback)
60 hours of operation. At the end of the Average Useful Life,
will pull hand and arm toward engine faster than you can let have the machine inspected annually by an authorized service
go. Broken bones, fractures, bruises or sprains could result. dealer to ensure that all mechanical and safety systems are
If situations occur which are not covered in this manual, use working properly and not worn excessively. Failure to do so can
in this manual
21.
care and good judgment. Call customer assistance for the
name of your nearest servicing dealer.
result in accidents, injuries or death.
and on the machine.
05.08.08
5
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | MTD 2N1, MTD 2P5, MTD Single Stage, MTD Snow Blower Manual |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
I would like to order a set of 2 Rubber Paddle (part #38) and a set of 4 Spiral-Crescent (part #39) for my Single-Stage Snow Thrower – Model 2N1. Is there a way to order those by Internet?