MTD 2N1 2P5 Single Stage Snow Blower Owners Manual

5
Recoil Starter
MruPnnOinRgT.ANT: Do not pull the starter handle with engine
To Engage Augers
1.  To engage the  augers and start throwing snow,
squeeze the auger control against the handle.
Release to stop the augers.
WARNING: To avoid unsupervised
engine operation, never leave the
engine unattended while running.  Turn
the engine off after use and  remove
ignition key.
Engaging the Drive
1.
Lifting up on the handle will allow the rubber  on the
augers to propel the snow thrower forward. Pushing
downward on the handle will raise the augers off the
ground and stop forward motion.
Operation
1.
Insert ignition key fully into slot. Make sure it snaps
into place. DO NOT turn ignition key. The engine
cannot start unless the key is inserted into ignition
switch.
NOTE: Excessive upward pressure on the handle  will
result in premature wear on the rubber auger blades
which would not be covered by warranty.
2.
3.
Move throttle control to FAST (rabbit) position.
2.
Run the engine for a few minutes before stopping to
help dry any moisture on the engine.
3.  Clean the snow thrower thoroughly after each  use.
Move choke to the ON position (cold engine start).  If
engine is warm, place choke in OFF position.
WARNING
4
.  Push primer three to five (3-5)  times, making sure to
cover vent hole when pushing. If engine is warm, push
primer only once. Always cover vent hole when push-
ing. Cool weather may require priming to be repeated.
Muffler, engine and
surrounding areas
become hot and
can cause a burn.
Do not touch.
5.
Pull gently on the starter handle until it begins to
resist, then pull quickly and forcefully to overcome the
compression. Do not release the handle and allow it to
snap back. Return rope SLOWLY to original position. If
required, repeat this step.
6.
As the engine warms, slowly rotate the choke control
to OFF position. If the engine falters, restart engine
and run with choke at half-choke position for a short
period of time, and then slowly rotate the choke into
OFF position.
Stopping the Engine
IMPORTANT:
WARNING: To avoid unsupervised  en-
For complete and
gine operation, never leave the engine
unattended while running. Turn the
engine off after use and remove ignition
key
detailed engine
starting, stopping and
storing instructions,
it is recommended
that you read the
engine manual also
included with
Run engine for a few minutes before stopping to help dry
off any moisture on the engine.
1.
2.
Move throttle control to STOP position.
Remove the ignition key. Removing the key will reduce
the possibility of unauthorized starting  of the engine
while equipment is not in use. Keep the key in a safe
place. The engine cannot start  without the ignition
key.
this unit.
NOTE:
3.
Wipe all snow and moisture from the area around the
engine as well as the area in and around the drive
control and auger control. Also, engage and release
both controls several times.
Excessive upward
pressure on the
handle will result in
premature wear
on the rubber
auger blades which
would not be covered
by warranty.
9
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “MTD 2N1 2P5 Single Stage Snow Blower Owners Manual

  1. I would like to order a set of 2 Rubber Paddle (part #38) and a set of 4 Spiral-Crescent (part #39) for my Single-Stage Snow Thrower – Model 2N1. Is there a way to order those by Internet?

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website