MTD Troy-Bilt LS 27 TB Log Splitter Lawn Mower Owners Manual

4
Control Handle
1.
2.
3.
Movewood.control handle FORWARD or DOWN to split
Releasement.     the control handle to stop  the wedge move-
Move control handle BACK or UP to return the wedge.
Operating
Your Log
Splitter
Log Dislodger
The log dislodger is designed to remove any partially
split wood from the wedge. This may occur while splitting
large diameter wood or freshly cut wood.
WARNING: Never remove partially  split
wood from the wedge with your hands.
Fingers may become trapped  between
split wood.
1.
2.
To remove partially split wood from wedge, move
control handle to REVERSE position until wedge is
fully retracted to allow split wood portion to contact  the
log dislodger.
Oncewood fromremovedoppositefrom endwedgeor inwithanotherlog dislodger,location.split
WARNING
Vertical Position
1.
Pulland thepivothorizontalthe beambeamto thelockverticalout toposition.release the beam
Never remove partially
split wood from the
wedge with your
Figure 4-3
Before Each Use
2.
To lock the beam in the vertical position,  pull out
on the vertical beam lock and rotate it to secure the
beam. See Figure 4-1.
1.  Remove the dipstick  and check hydraulic fluid level.
Refill if necessary. Approved fluids include Dexron®
III / Mercon® III automatic transmission fluid,  a
hands. Fingers may be-
come trapped between
split wood.
3.
Stand in front of the unit to operate the control handle
10
Weight AW hydraulic oil or Pro-Mix™ AW-32
and to stabilize the log. See Figure 4-3.
Hydraulic Oil.
2.
3.
4.
Check  engine oil level. Refill if necessary.
Fill up gasoline if necessary.
Horizontal Position
1.
Pull the vertical beam lock out and rotate it down. See
Figure 4-1. Pivot beam to the horizontal position. The
beam will lock automatically in horizontal position.
Standhandlebehindand tothestabilizereservoirthe log.tank to operate  control
Lubricate the beam area where splitting wedge will
slide with engine oil. Do not use grease to lubricate.
Make sure to lubricate both the front and the back of
the beam face.
2.
5.
Attach spark plug wire to the spark plug.
Operating Tips
Always:
Using the Log Splitter
1.
2.
Use clean fluid and check fluid level regularly.
1.
2.
Place the log splitter on level, dry ground.
Use an approved hydraulic fluid. Approved fluids
include Dexron® III / Mercon® III automatic transmis-
sion fluid, a 10 Weight AW hydraulic oil or Pro-Mix™
AW-32 Hydraulic Oil.
Place the beam in either the horizontal or vertical
position and lock in place with the appropriate
locking rod.
3.
4.
Block the front and back of both wheels.
3.
4.
5.
6.
Use a filter (clean or replace regularly).
Use a breather cap on fluid reservoir.
Make sure pump is mounted and aligned properly.
Useand pumpa flexibledrive“spider”shafts.type coupling between engine
Place the log against the end plate and only split
wood in the direction of the grain.
5.
To stabilize the log, place your hand only on sides of
log. Never place hand on the end between  the log
and the splitting wedge.
6.
Only one adult should stabilize the log and operate
the control handle, so the operator has full control
over the log and the splitting wedge.
10
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 40 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website