MTD Troy-Bilt LS 27 TB Log Splitter Lawn Mower Owners Manual

3
Setting Up
Your Log
Splitter
3.
4.
5.
Disconnectof the controlthevalve.log cradleSee Figurefrom the3-5.beam on the side
Liftintoandthe weldslide brackets.the cylinderSeeupFigureto the3-6.top  of beam and
Attach the dislodger over the wedge assembly  and
secure with hardware, previously removed, to the weld
brackets.
NOTE: Once the six hex screws are tightened, there
may be a slight gap between the dislodger and  the weld
brackets. This gap is normal.
6.
Reattach the log cradle to the side of the beam  with
the control valve, aligning the ends of the cradle with
the beam flanges.
Roll log splitter off the bottom crate.
7.
Preparing the Log Splitter
1.
2.
Lubricate the beam area (where the splitting  wedge
Figure 3-
will slide) with engine oil; do  not use grease.
Remove vented reservoir dipstick, which is located  in
front of the engine on top of the reservoir tank. See
Figure 3-7.
WARNING
Much of the original
fluid has been drawn
into the cylinder and
hoses. Make certain to
refill the reservoir to
prevent damage to the
hydraulic pump.
IMPORTANT: The log splitter may have been shipped
and primed with hydraulic fluid in the reservoir tank.
However, you MUST check the fluid level before operat-
ing. If not filled, proceed with the following steps:
3.
Fill the reservoir tank with hydraulic fluid included  with
this unit (if equipped) or approved fluids  which include
Dexron® III / Mercon® III automatic transmission  fluid,
a 10 Weight AW hydraulic oil or Pro-Mix™ AW-32
Hydraulic Oil.
4.
5.
6.
Checknot overfill.fluid level using the dipstick. See Figure 3-7. Do
Replace vented dipstick securely, tightening it until the
Figure 3-6
top of the threads are flush with top of the pipe.
Disconnect the spark plug and prime the  pump by
pulling the recoil starter as far as it will go. Repeat
approximately 10 times.
IMPORTANT:
The log splitter may
have been shipped and
primed with hydraulic
fluid in the reservoir
tank. If not, proceed
with the following
steps:
7.
8.
9.
Reconnect the spark plug wire and start  engine
following instructions in the OPERATION section.
Use control handle to engage the wedge to the
farthest extended position. Then retract  the wedge.
Refill tank as specified on the dipstick.
NOTE: Failure to refill the tank will void unit’s warranty.
10.
Extend and retract the wedge 12 complete cycles
to remove trapped air in the system (the system is
“self-bleeding”).
Refill reservoir within range marked on the dipstick.
WARNING: Much of the original
fluid has been drawn into the cylinder
and hoses. Make certain to refill  the
reservoir to prevent damage to the
hydraulic pump.
NOTE: Some fluid may
overflow from the vent
plug as the system
11.
builds heat and the
fluid expands and
Figure 3-7
seeks a balanced level.
NOTE: Some fluid may overflow from the vent plug as
the system builds heat and the fluid expands and seeks
a balanced level.
7
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 40 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website