MAINTENANCE AND REPAIR INSTRUCTIONS
NOTE: Maintenance, replacement, or repair of the emission
WARNING: To prevent serious injury, never
perform maintenance or repairs with unit running.
Always service and repair a cool unit. Disconnect the
spark plug wire to ensure that the unit cannot start.
control devices and system may be performed by a
Troy-Bilt or other qualified service dealer.
In order to assure peak performance of your engine, inspection
of the engine exhaust port may be necessary after 50 hours of
operation. If you notice lost RPM, poor performance or general
lack of acceleration, this service may be required. If you feel your
engine is in need of this inspection, refer service to a Troy-Bilt or
other qualified service dealer for repair. DO NOT attempt to
perform this process yourself as engine damage may result from
contaminants involved in the cleaning process for the port.
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should also
be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require special tools
or skills. If you are unsure about these procedures take
your unit to a Troy-Bilt or other qualified service dealer.
FREQUENCY
MAINTENANCE REQUIRED
SEE
Fill fuel tank with fresh fuel
Check oil
p. 6
Before starting engine
Every 10 hours
p. 11
Clean and re-oil air filter
p. 11
1st change at 10 hours
2nd change at 25 hours
Every 25 hours after
Change oil
p. 11
p. 11
p. 13
Change oil
Clean spark arrestor
10
Every 25 hours
Every 25 hours
hours on new engine
Check rocker arm to valve clearance and adjust
Check rocker arm to valve clearance and adjust
Check spark plug condition and gap
p. 12
p. 12
p. 13
BLADE REPLACEMENT
WARNING: To avoid serious personal injury,
5.
While holding the Allen wrench in the spindle hole, tighten the
nut by turning the wrench clockwise until tight (Fig. 17).
always wear gloves while handling, removing or
installing the blade.
NOTE: Make sure that the blade stays flat and centered
against the output shaft throughout installation.
1.
2.
Place the 5/16” Allen wrench in the spindle hole (Fig. 15).
While holding the Allen wrench in place, loosen the nut with
a 15/16” wrench by turning it counterclockwise (Fig. 15).
Spindle Hole
Tighten
Fig. 17
Loosen
WARNING: Verify the blade is flat against the
output shaft after the nut is tightened. If the blade
is off-center, the unit will be damaged by vibration,
and the blade may fly off, which can cause serious
personal injury.
Fig. 15
3.
Remove the nut and blade. Keep the nut for new blade
installation.
4.
Install the new blade and nut (Fig. 16).
ACCESSORIES/REPLACEMENT PARTS
Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 753-05562
Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 753-05549
Nut
Edger Blade
Use only original Troy-Bilt replacement parts.
Fig. 16
10
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals |
|---|---|
| Tags | MTD Troy-Bilt TBE515 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(3 votes, average: 2 out of 4)
Lawn and Garden readers have rated MTD Troy-Bilt TBE515 4 Cycle Lawn Edger Lawn Mower Owners Manual 2.0 out of 4.0 based on 3 product reviews. The manual tells you everything except HOW TO CHANGE THE BELT on the model TBE515
Easy to find parts and order them!
A total piece of junk; burns oil & engine seizes. Had to replace belt after second use. I invest in many lawn products but never again anything with a Troy-Bilt sticker!!!!!!!!!!!!!!!!