OPERATING INSTRUCTIONS
ASSEMBLING THE COUPLER
The following Troy-Bilt Add-Ons are also available for your unit:
NOTE: Aligning the release button with the guide recess
will help installation (Fig. 1).
Blower/Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBBV
Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC
Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBHS
Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBLE
Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . TBSS
Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBST
Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBTB
Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBTP
Removing the add-on
Coupler
Release Button
Primary Hole
Upper Shaft
Housing
Lower Shaft
Housing
WARNING: Read and understand operator’s
manual for unit to be used with this add-on
prior to operation.
Knob
Fig. 2
4.
Turn the knob clockwise to tighten (Fig. 3).
1.
2.
3.
Turn the knob counterclockwise to loosen (Fig. 1).
Press and hold the release button (Fig. 1).
CAUTION: Lock the release button in the
primary hole (Fig. 2) and securely tighten the
knob before operating this unit.
While firmly holding the upper shaft housing, pull the
turbo blower add-on out of the coupler (Fig. 2).
Installing the add-on
WARNING: To avoid serious personal injury
and damage to the unit, shut unit off before
removing or installing add-ons.
NOTE: To make installing or removing the add-on
easier, place the unit on the ground or on a
work bench.
Knob
1.
2.
3.
Remove the hanger from the top of the shaft housing.
Turn knob counterclockwise to loosen (Fig. 1).
While firmly holding the add-on, push it straight into
the coupler (Fig. 2).
Fig. 3
CAUTION: The add-ons with the coupler
system are to be used in the primary hole
only. Using the wrong hole could lead to
personal injury or damage to the unit.
The turbo blower add-on should be installed with the
release button in the primary hole.
Coupler
Release Button
Guide Recess
Check Flex Shaft Engagement Prior to Using
1.
2.
3.
4.
Start the unit.
Briefly engage and release the trigger.
Check that add-on is operating.
If the add-on is not operating, remove add-on and
repeat steps for installing the add-on.
5.
Recheck operation of add-on attachment.
Counterclockwise
Clockwise
Knob
Fig. 1
7
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Troy Bilt Snow Blower Manuals |
|---|---|
| Tags | MTD Snow Blower Manual, MTD TBTB Turbo, Troy Bilt TBTB Turbo |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)