Traction Control / Auger Control Lock
season and grease the fittings on the end of the auger
shaft with a standard grease gun. See Figure 12.
The cams on the ends of the control rods which
interlock the traction drive and auger drive controls
must be lubricated at least once a season or every 25
hours of operation. The cams can be accessed beneath
the handle panel. Use a multi-purpose automotive
grease.
Grease Fitting
Vent Plug
Gear Case
The gear case is equipped with a grease fitting on the
left housing and should be lubricated with Shell Alvania
grease EPR00, part number 737-0168 every 25 hours.
See Figure 12.
Do not overfill the gear case. Damage to the seals
could result. Be sure the vent plug is free of grease in
order to relieve pressure.
Auger Shaft
Plastic
Bearing
Plastic
Bearing
At least once a season, remove the shear bolts on the
auger shaft. Spray lubricant inside the shaft. Also
lubricate the plastic auger bearings at least once a
Shear Bolts
Figure 12
SECTION7: SERVICINGYOURSNOWTHROWER
WARNING: Before servicing, repairing, or
inspecting, disengage all clutch levers and
stop engine. Wait until all moving parts
have come to a complete stop. Disconnect
spark plug wire and ground it against the
engine to prevent unintended starting.
•
•
Remove the six carriage bolts, bell washers, and
hex nuts which attach them to the snow thrower.
Reassemble new skid shoes with the six carriage
bolts, bell washers (cupped side goes against skid
shoes) and hex nuts. Make certain the skid shoes
are adjusted to be level.
To remove shave plate, remove the carriage bolts, bell
washers, and hex nuts which attach it to the snow
thrower housing. Reassemble new shave plate, making
sure heads of the carriage bolts are to the inside of the
housing. Tighten securely.
Engine
Refer to the separate engine manual packed with your
unit for all engine maintenance procedures.
Augers
Belt Removal And Replacement
•
•
The augers are secured to the spiral shaft with two
shear bolts and hex lock nuts. If you hit a hard
foreign object or ice jam, the snow thrower is
designed so that the bolts may shear.
Auger Belts
•
Remove the plastic belt cover at the front of the
engine by removing the two self-tapping screws.
See Figure 13.
Refer to Figure 12.
If the augers will not turn, check to see if the bolts
have sheared. Replacement shear bolts and hex
lock nuts have been provided with the snow
thrower. When replacing bolts, spray an oil
lubricant into shaft before inserting new bolts.
Self-Tapping
Screw
IMPORTANT:NEVER replace the auger shear bolts with
standard hex bolts. Any damage to the auger gearbox
or other components as a result of doing so will NOT be
covered by your snow thrower’s warranty.
Shave Plate and Skid Shoes
Belt Cover
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary. To
remove the skid shoes, proceed as follows:
Figure 13
12
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, White Outdoor Snow Blower Manuals |
|---|---|
| Tags | MTD 1150W, MTD 850W, MTD Snow Blower Manual, White Outdoor Snow Boss 1150W, White Outdoor Snow Boss 850W |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2)
Lawn and Garden readers have rated MTD White Outdoor Snow Boss 850W 1150W Snow Blower Owners Manual 2.0 out of 2.0 based on 1 product reviews. I am trying to get information on the engine and this manual does not possess tyhat info and I can find no place on the web site that lists an engine manual.