Final Adjustments
Auger Control Adjustment
Check the adjustment of the auger control as follows:
•
Push forward on the auger control until the small
rubber bumper contacts the upper handle. There
should be slack in the cable. See Figure 5 .
Release the auger control. The cable should be
straight. Make certain you can depress the auger
control against the left handle completely without
using excess force.
•
If adjustment is necessary, proceed as follows:
•
Loosen the jam nut and thread the cable in (for less
slack) or out (for more slack) as necessary. See
Figure 5 .
•
Recheck the adjustment before retightening the
jam nut against the cable.
Skid
Shoes
Hex Nuts
Auger
Control
Figure 6
•
•
Retighten the hex nuts loosened earlier.
Repeat this adjustment on the skid shoe found on
the opposite side of the snow thrower.
Traction Control and Shift Lever Adjustment
To check the adjustment of the traction control and shift
lever, proceed as follows:
Z-End
Jam Nut
•
Move the shift lever into sixth (6) position.
a. With the traction control (refer to Figure 7)
released, squeeze in triggers and gently
push the snow thrower forward, then pull it
back. Disregarding the overall weight of the
snow thrower, the machine should otherwise
move freely.
Auger
Control Cable
Figure 5
b. Engage the traction control and attempt to
move them machine both forward and
rearward. You should experience resistance
as the wheels should not be turning.
Move the shift lever into the fast reverse (R2)
position and repeat the previous steps (a & b).
If you experienced resistance either when repositioning
the shift lever from 6 to R2 or when attempting to move
the machine forward or rearward with the traction
control released, your snow thrower’s traction control is
in need of adjustment and you should NOT operate the
machine before completing the adjustment as follows:
Skid Shoe Adjustment
The space between the shave plate and the ground can
be adjusted by repositioning the skid shoes found on
either side of the snow throwers auger housing. For
close snow removal, place skid shoes in the low
position. Use middle or high position when area to be
cleared is uneven. See Figure 6.
•
IMPORTANT: It is NOT recommended that this snow
thrower be operated on a gravel surface, as loose
stones can be easily picked up and thrown by the
machine. If you must operate on a gravel surface,
ALWAYS adjust the skid shoes into the HIGH position
to allow the shave plate maximum clearance.
•
Loosen the jam nut on the traction control cable
and UNTHREAD the cable one full turn.
Recheck the adjustment.
Retighten the jam nut to secure the cable when
correct adjustment is reached.
If the machine can be moved freely both forward and
rearward when the traction control fully depressed,
proceed as follows:
Adjust skid shoes as follows:
•
•
•
Loosen, but do NOT remove, the three hex nuts
which fasten the skid shoe to the auger housing.
Raise or lower the skid shoe to desired position.
•
NOTE: Make certain the entire base of both skid shoes
are against the ground to avoid uneven wear on the
skid shoes. When one side does wear out, the skid
shoes are reversible.
•
Loosen the jam nut on the traction drive cable and
THREAD the cable in one full turn.
6
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, White Outdoor Snow Blower Manuals |
|---|---|
| Tags | MTD 1150W, MTD 850W, MTD Snow Blower Manual, White Outdoor Snow Boss 1150W, White Outdoor Snow Boss 850W |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2)
Lawn and Garden readers have rated MTD White Outdoor Snow Boss 850W 1150W Snow Blower Owners Manual 2.0 out of 2.0 based on 1 product reviews. I am trying to get information on the engine and this manual does not possess tyhat info and I can find no place on the web site that lists an engine manual.