ENGLISH
9.
Push the primer button (9). Every time you
push the primer button (9), wait two sec-
onds. For the number of times required to
push the primer button (9), see the engine
manufacturer’s instructions.
(Electric Start) Push on the electric start
button (10) until the engine starts. Do not
crank for more than 10 seconds at a time.
The electric starter is thermally protected. If
the electric starter overheats, it will automati-
cally stop and can only be restarted when it
has cooled to a safe temperature. A wait of
about 5 to 10 minutes is required to allow the
electric starter to cool.
(Recoil Start) Rapidly pull the recoil starter
handle (12). Do not allow the recoil starter
handle (12) to snap back. Slowly return the
recoil starter handle (12).
If the engine does not start in 5 or 6 tries,
See the “Trouble Shooting Chart” Instruc-
tions.
(Electric Start) When the engine starts, re-
lease the electric start button (10) and
move the choke control (14) to 1/2 choke
position. When the engine runs smoothly,
move the choke control (14) to the off posi-
tion.
(Electric Start) First disconnect the power
cord from the three–hole receptacle. Then,
disconnect the power cord from the switch
NOTE:box (11)In. temperatures below 05F, allow
the engine to warm up for several minutes
before blowing snow.
When throwing snow, always run the engine
with the throttle control (13) in the fast posi-
tion.
How To Start A Warm Engine (Figure 2)
2. Move the throttle control (13) to the stop
position.
If an engine has been running and is still warm,
leave the choke control (14) in the off position
and do not push the primer button (9). If the
engine fails to start, follow the instructions “How
To Start A Cold Engine”.
3.
Remove (do not turn) the ignition key (8).
4. Disconnect the spark plug wire.
5. Do not place your hands in the auger hous-
ing (4) or the discharge chute (3). Use a
pry bar to remove any snow or debris.
10.
NOTE: Do not use the primer button (9) to
start a warm engine.
How To Start An Engine With A Frozen Electric Snow Throwing Tips
Starter (Figure 2)
1. For maximum snow thrower efficiency,
change the ground speed, NEVER change
the engine speed. The engine is designed to
deliver maximum performance at full throttle
and must be run in the fast position at all
times. In deep, freezing, or wet snow, reduce
forward speed. If the wheels slip, also reduce
forward speed.
If the electric starter is frozen and will not turn
the engine, follow the instructions below.
11.
1.
Pull out the recoil starter handle (12) as far
as possible.
2.
Quickly release the recoil starter handle
12.
13.
(12). Allow the recoil starter handle (12) to
snap back against the recoil starter.
2. Most efficient snow throwing is accomplished
when the snow is removed immediately after
if falls.
If the engine still fails to start, repeat the two pre-
vious steps until the engine starts. Then, contin-
ue with the directions “How To Start A Cold
Engine”.
3. For complete snow removal, slightly overlap
each previous path.
To help prevent the possible freeze–up of the
recoil starter and of the engine controls, proceed
as follows after each snow removal job.
4.
Whenever possible, discharge the snow
down wind.
14.
15.
5.
For normal usage, set the skids so that the
scraper bar is 1/8” above the skids. For ex-
tremely hard–packed snow surfaces, adjust
the skids upward so that the scraper bar
touches the ground.
1.
With the engine running, quickly pull the re-
coil starter handle (12) three or four times
with a continuous full arm stroke. This will
produce a loud clattering sound that is not
harmful to the engine or starter.
6.
7.
Rocks and gravel must not be picked up and
thrown by the machine. On gravel or crushed
rock surfaces, set the skids at 1–1/4 inch be-
low the scraper bar. See “How To Adjust The
Height Of The Skids” in the Maintenance
section.
2.
Stop the engine. Wipe all snow and moisture
from the carburetor cover, control levers and
cables. Also move the throttle control (13),
choke control (14), and recoil starter han-
dle (12) several times.
WARNING: Never run the engine
indoors or in enclosed, poorly ven-
tilated areas. Engine exhaust con-
After each snow throwing job, allow the en-
gine to idle for a few minutes. The snow and
accumulated ice will melt off the engine.
How To Remove Snow or Debris From
The Auger Housing (Figure 2)
WARNING: Do not attempt to re-
move snow or debris that may be-
come lodged in auger housing
tains carbon monoxide, an odorless and
deadly gas. Keep hands, feet, hair and
loose clothing away from any moving parts
located on the engine or the snow thrower.
The temperature of muffler and nearby
areas may exceed 150°F. Avoid these
areas.
8. Clean the snow thrower after each use.
9. Remove ice, snow and debris from the entire
snow thrower. Flush with water to remove all
salt or other chemicals. Wipe snow thrower
dry.
without taking the following precautions.
1. Release the auger drive lever (5).
F–031015L
15
| Categories | Murray Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Murray 627850X5A |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)