Murray 627850X5A Snow Blower Owners Manual

ENGLISH
signed to break and protect the machine if an
object becomes lodged in the auger housing.
Do not use a harder bolt as the protection pro-
vided by the shear bolt will be lost.
WARNING: For safety and to pro-
tect the machine, use only original
equipment shear bolts.
To replace a broken shear bolt, proceed as fol-
lows. Extra shear bolts were provided in the as-
sembly parts bag.
5.  Thoroughly clean the snow thrower.
Replacement parts, except for the engine,
transmission, transaxle or differential, are
available from the store where the product was
purchased, a service shop recommended by the
store or from a “Murray, Inc. Central Parts
Distributor” listed on the back page of this
Instruction Book.
If you are unable to obtain parts or service in the
manner outlined above, then contact:
USA – MURRAY, INC.
Outdoor Power Equipment
Customer Service Department
P.O. Box 268
Brentwood, Tennessee  37027
1–800–251–8007
6.
Lubricate all lubrication points. See the Main-
tenance section.
7.
Be sure that all nuts, bolts and screws are
securely fastened. Inspect all visible  moving
parts for damage, breakage and wear. Re-
place if necessary.
8.
Cover the bare metal parts of the blower
housing, auger, and the impeller with spray
rust preventative lubricant.
1.
2.
3.
4.
(Figure 2) Move the throttle control (13) to
the stop position. Disengage all controls.
Disconnect the spark plug wire. Make sure
all moving parts have stopped.
(Figure 14) Lubricate the auger shaft Zerk
fitting (1), if equipped, with a grease gun.
(Figure 25) Align the hole in the auger with
the hole in the auger shaft. Install the new
shear bolt (2), spacer (3) and locknut (4).
Connect the spark plug wire.
9.
Put the unit in a building that has good ven-
tilation.
10.
If the machine must be stored outdoors,
block up the snow thrower to be sure the en-
tire machine is off the ground.
11.
Cover the snow thrower with a suitable pro-
tective cover that does not retain moisture.
Do not use plastic.
CANADA – MURRAY CANADA, INC.
Factory Customer Service
1195 Coutneypark Drive East
Mississauga, Ont. L5T–1R1
5.
1–800–661–6662
be accepted.
Collect telephone calls will not
How To Prepare The Snow Thrower For
How To Order Replacement Parts
Storage
Replacement parts for the engine, transaxle, or
transmission, are available from the
manufacturer’s authorized service center found
in the yellow pages of the telephone directory.
Also, see the individual engine or transmission
warranties to order replacement parts.
WARNING: Do not remove gasoline
while inside a building, near a fire,
or while you smoke. Gasoline
fumes can cause an explosion or a fire.
The replacement parts are shown either on the
back pages of this Instruction Book or in a
separate Parts List Book.
Use only manufacturer’s authorized or approved
replacement parts. The letter placed on the end
of the part number denotes the type of finish for
the part, C for chrome, Z for zinc, a PA for
purchased assembly. It is important that you
include this when ordering a part. Do not use
attachments or accessories not  specifically
recommended for this unit. In order to obtain
proper replacement parts you must supply the
model number (see nameplate).
1.
2.
3.
Drain the fuel tank.
Let the engine run until it is out of gasoline.
Drain the oil from the warm engine. Fill the
engine crankcase with new oil.
When ordering the following information is
required:
(1)
(2)
(3)
(4)
The Model Number
Serial Number
Part Number
Quantity
4.
Remove the spark plug from the cylinder.
Pour one ounce of oil into the cylinder. Slow-
ly pull the recoil–start grip so that the oil will
protect the cylinder. Install a new spark plug
in the cylinder.
TROUBLE SHOOTING CHART
TROUBLE
CAUSE
CORRECTION
Difficult starting
Defective spark plug.
Water or dirt in fuel system.
Replace spark plug.
Use carburetor bowl drain to flush and refill with
fresh fuel.
Engine runs erratic
Engine stalls
Blocked fuel line, empty gas tank, or stale
gasoline
Clean fuel line; check fuel supply; add fresh
gasoline
Unit running on CHOKE.
Set choke lever to RUN position.
Engine runs erratic;
Loss of power
Water or dirt in fuel system.
Use carburetor bowl drain to flush and refill with
fresh fuel.
Excessive vibration
Loose parts: damaged impeller
Stop engine immediately and disconnect spark
plug wire.  Tighten all bolts and make all
necessary repairs.  If vibration continues, have
the unit serviced by a competent repairman.
Unit fails to propel itself
Drive belt loose or damaged.
Replace drive belt.
Incorrect adjustment of traction drive cable
Worn or damaged friction wheel.
Auger drive belt loose or damaged.
Auger control cable not adjusted correctly.
Shear bolt broken
Adjust traction drive cable.
Replace friction wheel.
Unit fails to discharge snow
Adjust auger drive belt; replace if damaged.
Adjust auger control cable.
Replace shear bolt
Discharge chute clogged.
Stop engine immediately and disconnect spark
plug wire.  Clean discharge chute and inside of
auger housing.
Foreign object lodged in auger
Stop engine immediately and disconnect spark
plug wire.  Remove object from auger.
F–031015L
19
Product Specification
CategoriesMurray Snow Blower Manuals, Snow Blower Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 52 pages
Document File TypePDF
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website