ENGLISH
MAINTENANCE CHART
CUSTOMER RESPONSIBILITIES
SERVICE RECORDS
Fill in dates as you
complete regular
service.
Before
Each
Use
First
2
Hours
Every
5
Hours
Every
10
Hours
Every
25
Hours
Each
Season
Before
Storage
SERVICE DATES
Check Engine Oil Level
Change Engine Oil
√
√
√
√
√
√
√
Check And Tighten All Screws and Nuts
Check Spark Plug
Adjust Drive Belt
Check Fuel
√
√
√
√
√
√
Drain Fuel
√
√
Check Auger Clutch Cable Adjustment
(See Cable Adjustment)
√
√
√
√
Check Traction Clutch Cable Adjustment
(See Cable Adjustment)
Lubricate All Pivot Points
√
√
√
Lubricate Auger Shaft
(See Shear Bolt Replacement)
√
√
Lubricate Drive Chains and Sprockets
MAINTENANCE
All adjustments in the Maintenance section of
this manual should be checked at least once
each season.
2. Remove the gas from the gas tank. Stand
the snow thrower up on the front end of the
auger housing (4).
NOTE: Illustrations begin on page 3.
WARNING: Drain the gasoline out-
doors, away from fire or flame.
Use the following maintenance section to keep
your unit in good operating condition. All the
maintenance information for the engine is in the
engine manufacturer’s instructions. Before you
start the engine, read this book.
As Required
The following adjustment should be preformed
more than once each season.
3. (Figure 21) Loosen the bolts (3) on each
side of the bottom panel (2).
Remove the bottom panel (2).
(Figure 15) Lubricate the chains (5) with a
chain type lubricant.
1.
Adjust the auger drive belt after the first 2 to
4 hours, again at mid–season, and twice
4.
5.
WARNING: Before you make an in-
spection, adjustment (except
carburettor), or repair, disconnect
the wire from the spark plug.
each season thereafter. See “How To Adjust
The Auger Drive Belt” in the Maintenance
section.
6. Wipe the hexshaft and sprockets (6) with
5W30 motor oil.
NOTE: If grease or oil come in contact
with the disc drive plate (1) or the friction
wheel (3), damage can result. Clean off
any oil or grease with a alcohol base sol-
vent.
7. (Figure 21) Install the bottom panel (2).
8. Tighten the bolts (3) on each side of the bot-
tom panel (2).
General Recommendations
Lubrication
The warranty on this snow thrower does not cov-
er items that have been subjected to operator
abuse or negligence. To receive full value from
the warranty, the operator must maintain the
snow thrower as instructed in this manual.
Every 10 Hours
1.
Lubricate the Zerk fittings (1) every ten
hours with a grease gun.
2.
Each time a shear bolt is replaced, the auger
shaft must also be greased.
Some adjustments must be made periodically to
properly maintain the snow thrower.
3. Lubricate all pivot points.
Every 25 Hours (Figure 15)
Chute Rotation Gear
Items Not To Lubricate (Figure 15)
G
Check for any loose or damaged parts.
After Each Use
1. Do not lubricate the hex shaft and sprock-
ets (6). All bearings and bushings are life-
time lubricated. For storage, put a slight
amount of 5W–30 motor oil on a cloth and
wipe the hex shaft and sprockets (6) to
prevent rust.
G
G
G
Tighten any loose fasteners.
Check and maintain the auger.
(Figure 4) Lubricate the chute rotation gear (1)
with automotive type oil.
2.
If grease or oil comes in contact with the
disc drive plate (1) or the friction wheel
Check controls to make sure they are
functioning properly.
G
If any parts are worn or damaged, replace
immediately.
Chains
(3), the friction wheel (3) can be damaged.
1.
(Figure 2) Move the speed shift lever (6) to
first gear.
Make sure to thoroughly clean the disc drive
plate (1) and the friction wheel (3).
F–031015L
16
| Categories | Murray Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Murray 627850X5A |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)