Simplicity 555 755 1693646 1693647 1693648 1693649 Series Snow Blower Owners Manual

Regular Maintenance
NORMAL CARE
CARE REQUIRED
FREQUENCY
LUBRICATION
Simplicity Winter Weight
Worm Gear Oil
Check auger gear case lubrication.**
Lubricate snowthrower.
25 Hours
10 Hours     10W Oil  and Grease
Check tire pressure.
Monthly
N/A
Change engine oil.*
50 Hours✛     See Engine Manual
Clean or replace spark plug.
Check drive linkage/belt tension
Yearly
See Engine Manual
N/A
4-6 Hours
*
Change original oil after two hours of operation.
Check oil level each fall and spring.
**
See your engine Owner’s Manual.
OFF-SEASON STORAGE
5.
6.
Start the engine outdoors. Warm up engine by run-
ning at SLOW speed for a a few minutes before run-
ning at FAST speed, or blowing snow.
Check the operation of all the controls. If necessary,
lubricate the snowthrower to improve operation of the
chute control.
Before you store your snowthrower for the off-season,
read the Maintenance and Storage instructions in the
Safety Rules section and take the following precautions:
NOTE: Gasoline, if permitted to stand unused for extend-
ed periods (30 days or longer), may develop gummy
deposits which can adversely affect the engine carbure-
tor and cause engine malfunction. To avoid this condi-
tion, add Simplicity Gasoline Stabilizer to the fuel tank, or
drain all fuel from the system before placing unit in stor-
age.
CHECK AUGER
GEAR CASE LUBRICATION
1.
2.
3.
Place the snowthrower on a level surface.
Remove the Pipe Plug (Figure 16).
1.
2.
3.
Prepare your snowthrower engine for storage as
instructed in the Engine Owner’s Manual.
Check the lubricant level. It should be level with the
lower edge of the plug opening. If not, add Simplicity
Winter Weight Worm Gear Oil (available from your
dealer).
Lubricate the snowthrower as described in the
LUBRICATION section of this manual.
Clean the snowthrower thoroughly. Coat exposed
bare metal parts with a quality paint (available from
you dealer) or a light film of grease, oil or automotive
wax.
4.
Re-install Pipe Plug, and tighten securely.
4.
5.
Store snowthrower in the wheels down, operating
position. Note: If the unit is stored in any other posi-
tion, oil from crankcase could enter cylinder head,
causing a service problem.
Store the unit in a protected area and cover.
STARTING AFTER STORAGE
1.
Remove the spark plug and wipe dry. Crank the
engine a few times to blow excess oil out of plug hole.
Then reinstall plug.
2.
3.
4.
Fill fuel tank with fresh gasoline (unless a fuel stabiliz-
er was used).
Check to be sure engine fins are clean and air flow is
unobstructed.
Pipe Plug
Check engine oil level and lubricate snowthrower.
Change oil if necessary.
Figure 16.  Checking Auger Gear Case Lubrication
13
Product Specification
CategoriesSimplicity Snow Blower Manuals, Snow Blower Manuals
Tags, , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 30 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandSimplicity, Snow Blower
Document File TypePDF
Publishersimplicitymfg.com
Wikipedia's PageSimplicity Outdoor
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website