Simplicity Snapper 1695302 1695311 1695410 1695313 1695314 1695411 Intermediate Frame Snow Blower Owners Manual

Adjustments
AUGER DRIVE ADJUSTMENT
WARNING
WARNING
Do not over-tighten, as this may cause traction
drive to engage without depressing the traction
drive control (arm must remain in up position).
Do not over-tighten, as this may lift the lever
and cause auger drive to be engaged without
depressing the Auger Control.
Verify that the cables are not over-tightened:
With speed selector in position 1 and traction
drive control fully released, push snowthrower
forward. The unit should move forward freely.
1.
With the drive lever released, the hook (B, Figure
20) should barely touch the lever (C) without
raising it. There can be a maximum 1/32”
clearance as shown.
If unit does not move forward freely, the cable
has been over-tightened. To remedy, loosen
tension on clutch cable slightly, and recheck.
2.
To adjust, loosen nut (D) by holding the adjusting
flats (A) and turning nut (D).  Turn adjustment flats
and hold screw.  The adjustment screw (E) is a
phillips screw and the head can be held or turned
by inserting a screwdriver through the spring (F).
3.
4.
Hold adjusting flats (A) and tighten nut (D).
TRACTION DRIVE ADJUSTMENT
Start unit and check auger.  Auger must not be
engaged unless auger control is depressed.
Initial Adjustment
5.
6.
7.
8.
With engine running, fully depress auger control,
the auger should engage and run normally.
1.  With the drive lever released there should be slack
in the cable when moved slightly from side to side.
Release auger control. Auger must stop within 5
seconds.
2.  To adjust tension on the cable slide the cable boot
(A, Figure 21) off the cable adjustment bracket (D).
If auger does not operate properly, stop engine
and recheck drive linkage adjustments.
3.  Move the “Z” hook (C) from the cable adjustment
bracket (D) to a different adjustment hole. The
cable should have slack.  The cable should have
no tension or load.
If auger linkage is properly adjusted, auger drive
belt tension may require adjustment. See adjusting
the auger belt in this section of the manual
Note: If the cable is too slack the unit will not drive.  If
the cable is too tight the drive will be engaged without
pushing the handle down.
A
4.
Slide the cable boot (A) over the cable adjustment
bracket.
D
E
A
F
B
B
1/32”
(.080 cm)
C
C
B
D
Figure 20.  Auger Drive Adjustment
A.  Adjusting Flats
B.  Spring Hook
C
Figure 21.  Traction Drive Cable Adjustment
A.  Cable Boot
C.  Lever
D.  Adjustment Nut
E.  Adjustment Screw
F.  Spring
B.  Traction Drive Cable
C.  “Z” Hook
D.  Cable Adjustment Bracket
26
Product Specification
CategoriesSimplicity Snow Blower Manuals, Snapper Snow Blower Manuals, Snow Blower Manuals
Tags, , , , , , , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 38 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandSimplicity, Snow Blower
Document File TypePDF
Publishersimplicitymfg.com
Wikipedia's PageSimplicity Outdoor
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website