Toro 07154SL Service Manualpdresser 1800 2500 Preface Publication

Removal (Fig. 33)
Empty Topdresser hopper and position machine on
a level surface. Chock wheels to prevent machine from
moving. If Topdresser is attached to tow vehicle, engage
tow vehicle parking brake, stop engine and remove key
from the ignition switch.
5.  Slide wheel motor shaft into sprocket while removing
the dowel in sprocket bore that was placed during the re-
moval process.  Align motor  mounting holes  with car-
riage bolt and stud on frame. Place flat washer (item 12)
and lock nut (item 11) on carriage bolt and stud but do
not fully tighten.
1.
6.
Apply Loctite #242 (or equivalent) to  threads of set
2.
that secure wheel motor to frame.
Loosen but do not remove two (2) lock nuts (item 11)
screws (item 14). Center sprocket in cradle and secure
in  position with  two  (2)  set  screws. Make  sure  that
sprocket does  not contact head  of carriage bolt  (item
24).
3.
and flat washer (item 15) from wheel motor shaft.
Remove cap screw (item 16), lock washer (item 17)
7.
screw (item 16). Install cap screw, lock washer (item 17)
and flat washer (item 15) into wheel motor shaft.
Apply Loctite #242 (or equivalent) to threads of cap
4.
sprocket to wheel motor shaft.
Loosen  two (2)  set  screws (item  14)  that secure
5.
Installing Hydraulic System Components at  the begin-
ning of the Service and Repairs section of this chapter.
Read the  General  Precautions for  Removing and
8.
so tight that binding occurs  on sprockets. Tighten lock
nuts to secure motor to cradle.
Rotate wheel motor to take slack out of chain, but not
6.
poses. Thoroughly  clean hydraulic  hoses and  fittings
prior to loosening hydraulic lines at wheel motor.
Label all  hydraulic  connections for  assembly pur-
9.
mid–span between sprockets.  If necessary, reposition
wheel motor to allow correct chain deflection.
Check that chain has 0.125” (3.2 mm) deflection  at
7.
Disconnect hydraulic lines from fittings on wheel mo-
10.Remove
lines and fittings during disassembly.
caps or plugs that were put on any hydraulic
tor. Allow hydraulic oil to drain from lines into a suitable
container. Put caps or plugs on open hydraulic lines and
fittings to prevent contamination. Remove and  discard
O–rings.
11.
Lubricate new O–rings with  clean hydraulic oil and
position on fittings. Using labels made during removal,
correctly connect and secure hydraulic hoses to hydrau-
lic fittings on wheel motor.
8.
move two (2) lock nuts (item 11) and flat washers (item
Support wheel motor to prevent it from shifting. Re-
12)
9.
that secure motor to machine.
Antiseize
Lubricant
Slide wheel motor from sprocket and machine. While
2
sliding  wheel motor  from  sprocket, insert  dowel  into
sprocket bore to  support sprocket and chain  in cradle
assembly. Locate and  retrieve square key from  motor
shaft.
Loctite #242
3
10.If
required,  remove hydraulic  fittings and  O–rings
from the wheel motor. Discard O–rings.
Installation (Fig. 33)
1
8
1.
If removed, install hydraulic fittings with new O–rings
into the wheel motor ports (see Hydraulic Fitting Installa-
tion in the General Information section of this chapter).
6
7
2.
Apply antiseize lubricant to wheel motor shaft. Posi-
5
4
tion square key into motor shaft slot.
3.
Make  sure  that roller  chain  is  positioned  around
Figure 34
wheel motor sprocket and that hub of sprocket is away
from wheel motor position.
1.
2.
3.
4.
Hydraulic motor
Square key
Set screw (2 used)
Cap screw
5.
6.
7.
8.
Lock washer
Flat washer
Sprocket
Drive chain
4.
Make sure  that carriage  screw is placed  in cradle
hole.
Topdresser 1800 & 2500
Page 3 – 39
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 100 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website